Geology topics

J. R. Nimmo

Publications and source records attributed to J. R. Nimmo.

23 records · Page 2Linked to original sources

USGS1997

Modeling structural influences on soil water retention

A new model quantities the effect of soil structure, considered as the arrangement of particles in the soil, on soil water retention. The model partitions the pore space into texture-related and structure-related components, the textural component being what can be deduced to exist if the arrangement of the particles were random, and the structural component being the remainder. An existing model, based on particle-size distributions, represents the textural component, and a new model, based on aggregate-size distributions, represents the structural component. This new model makes use of generalized properties that vary little from one medium to another, thereby eliminating any need for empirically tilted parameters. It postulates a particular character of the structural pore space that in same ways resembles texture-related pore space, but with pore shape related to the breadth of the aggregate-size distribution. To predict a soil water retention curve, this model requires the soil's porosity and particle- and aggregate-size distributions. Tested with measurements for 17 samples from two sources, it fits the data much better than does a model based on texture alone. Goodness of fit indicated by correlation coefficients ranged from 0.908 to 0.998 for the new model, compared with a range of 0.686 in 0.955 for the texture-based model.

Soil Science Society of America Journal↗

USGS1994

The feasibility of recharge rate determinations using the steady-state centrifuge method

The establishment of steady unsaturated flow in a centrifuge permits accurate measurement of small values of hydraulic conductivity ( K ). This method can provide a recharge determination if it is applied to an unsaturated core sample from a depth at which gravity alone drives the flow. A K value determined at the in situ water content indicates the long-term average recharge rate at a point. Tests of this approach have been made at two sites. Unsaturated K values were measured easily for sandy core samples from a site in the San Joaquin Valley of California. The results indicate that a better knowledge of the matric pressure profiles is required before a recharge rate can be determined. Fine-textured cores from a site in southeastern Washington required new developments of apparatus and procedures, especially for making centrifuge measurements with minimal compaction of the samples. Measured K values led to preliminary recharge rate determinations that are reasonable considering the known hydrology and topography of the site.

Soil Science Society of America Journal↗

USGS1992

Semiempirical model of soil water hysteresis

In order to represent hysteretic soil water retention curves accurately using as few measurements as possible, a new semiempirical model has been developed. It has two postulates related to physical characteristics of the medium, and two parameters, each with a definite physical interpretation, whose values are determined empirically for a given porous medium. One parameter represents the fraction of the pore space that is not subject to Haines jump hysteresis. Its associated postulate is that a single value of this parameter characterizes a given medium, or, equivalently, that the medium is self-similar with respect to the division between hysteretic and nonhysteretic pore space. The second parameter is the effective body-to-neck size ratio of the medium's largest pore. The second postulate specifies a particular relation between the size distributions of pore bodies and of pore necks. Tests of the model show that it provides high-quality optimized fits to measured water content vs. matric pressure wetting curves for a wide variety of media. The parameter values obtained through optimization correlate plausibly with such media properties as uniformity of particles, complexity of structure, and degree of compaction. A practical use of this model is to provide a complete simulated main wetting curve for a medium where only a main drying curve and two points on the wetting curve have been measured. With additional development, it may be possible to do without the two measured wetting points if parameters can be evaluated from other measurements or known properties of the medium.

Soil Science Society of America Journal↗

USGS1992

Improved apparatus for measuring hydraulic conductivity at low water content

A modification of the steady-state centrifuge method (SSCM) for unsaturated hydraulic conductivity ( K ) measurement improves the range and adjustability of this method. The modified apparatus allows mechanical adjustments to vary the measured K by a factor of 360. In addition, the use of different flow-regulating ceramic materials can give a total K range covering about six orders of magnitude. The increment of K adjustment is a factor of about 1.6. This makes it potentially useful for measuring targeted values of K or, through a trial and error procedure, of water content (θ). The range extension afforded by this modification has led to the lowest steady-state K measurement to date: 1.1 × 10 −11 m/s at θ of 0.068 m 3 water/m 3 for a sandy soil of the Delhi series (mixed, thermic Typic Xeropsamment).

Soil Science Society of America Journal↗

USGS1986

The temperature dependence of isothermal moisture vs. potential characteristics of soils

A method has been developed for rapid, transient measurement of hysteretic soil-moisture characteristics as a function of temperature. While a varying soil-water pressure was imposed on a thin sample by means of flexible membranes held in firm contact with the soil, water content was measured by gamma-ray attenuation, and matric potential was measured with tensiometers. The applied pressure was cycled through a program designed to obtain hysteretic θ(ψ) main and scanning curves. Isothermal characteristics were measured for 181-µm glass beads, Plainfield (Typic Udipsamments) sand, and an undisturbed core of Plano (Typic Argiudolls) silt loam at several temperatures in the 4° to 50°C range. At each temperature the measurements included main drying and wetting curves covering the θ range from 0.30 to 0.05 m 3 water/m 3 for glass beads, 0.30 to 0.17 for sand, and 0.45 to 0.37 for silt loam. A model has been developed to quantify the temperature dependence as a function of θ. Combined with an isothermal hysteresis model of Mualem, this model requires only three characteristic functions to represent all hysteretic θ(ψ) curves for a given medium at all temperatures. Model calculations for the sand and silt loam data indicate that except near saturation, the temperature effect is greater than can be accounted for by the temperature dependence of the surface tension of pure water. The results rule out several possible explanations but they support the hypothesis that the concentration and effectiveness of dissolved surfactants increases with temperature.

Soil Science Society of America Journal↗