Simulation-optimization modeling to assist conjunctive management of stream-aquifer systems of Rhode Island
Explore the source record for details and available documents.
Rhode Island↗
Geology topics
Gregory E. Granato
Publications and source records attributed to Gregory E. Granato.
Kendall-Theil Robust Line (KTRLine--version 1.0)-A Visual Basic Program for Calculating and Graphing Robust Nonparametric Estimates of Linear-Regression Coefficients Between Two Continuous Variables
The Kendall-Theil Robust Line software (KTRLine-version 1.0) is a Visual Basic program that may be used with the Microsoft Windows operating system to calculate parameters for robust, nonparametric estimates of linear-regression coefficients between two continuous variables. The KTRLine software was developed by the U.S. Geological Survey, in cooperation with the Federal Highway Administration, for use in stochastic data modeling with local, regional, and national hydrologic data sets to develop planning-level estimates of potential effects of highway runoff on the quality of receiving waters. The Kendall-Theil robust line was selected because this robust nonparametric method is resistant to the effects of outliers and nonnormality in residuals that commonly characterize hydrologic data sets. The slope of the line is calculated as the median of all possible pairwise slopes between points. The intercept is calculated so that the line will run through the median of input data. A single-line model or a multisegment model may be specified. The program was developed to provide regression equations with an error component for stochastic data generation because nonparametric multisegment regression tools are not available with the software that is commonly used to develop regression models. The Kendall-Theil robust line is a median line and, therefore, may underestimate total mass, volume, or loads unless the error component or a bias correction factor is incorporated into the estimate. Regression statistics such as the median error, the median absolute deviation, the prediction error sum of squares, the root mean square error, the confidence interval for the slope, and the bias correction factor for median estimates are calculated by use of nonparametric methods. These statistics, however, may be used to formulate estimates of mass, volume, or total loads. The program is used to read a two- or three-column tab-delimited input file with variable names in the first row and data in subsequent rows. The user may choose the columns that contain the independent (X) and dependent (Y) variable. A third column, if present, may contain metadata such as the sample-collection location and date. The program screens the input files and plots the data. The KTRLine software is a graphical tool that facilitates development of regression models by use of graphs of the regression line with data, the regression residuals (with X or Y), and percentile plots of the cumulative frequency of the X variable, Y variable, and the regression residuals. The user may individually transform the independent and dependent variables to reduce heteroscedasticity and to linearize data. The program plots the data and the regression line. The program also prints model specifications and regression statistics to the screen. The user may save and print the regression results. The program can accept data sets that contain up to about 15,000 XY data points, but because the program must sort the array of all pairwise slopes, the program may be perceptibly slow with data sets that contain more than about 1,000 points.
Techniques and Methods↗
Effects of alternative instream-flow criteria and water-supply demands on ground-water development options in the Big River Area, Rhode Island
Transient numerical ground-water-flow simulation and optimization techniques were used to evaluate potential effects of instream-flow criteria and water-supply demands on ground-water development options and resultant streamflow depletions in the Big River Area, Rhode Island. The 35.7 square-mile (mi2) study area includes three river basins, the Big River Basin (30.9 mi2), the Carr River Basin (which drains to the Big River Basin and is 7.33 mi2 in area), the Mishnock River Basin (3.32 mi2), and a small area that drains directly to the Flat River Reservoir. The overall objective of the simulations was to determine the amount of ground water that could be withdrawn from the three basins when constrained by streamflow requirements at four locations in the study area and by maximum rates of withdrawal at 13 existing and hypothetical well sites. The instream-flow requirement for the outlet of each basin and the outfall of Lake Mishnock were the primary variables that limited the amount of ground water that could be withdrawn. A requirement to meet seasonal ground-water-demand patterns also limits the amount of ground water that could be withdrawn by up to about 50 percent of the total withdrawals without the demand-pattern constraint. Minimum water-supply demands from a public water supplier in the Mishnock River Basin, however, did not have a substantial effect on withdrawals in the Big River Basin. Hypothetical dry-period instream-flow requirements and the effects of artificial recharge also affected the amount of ground water that could be withdrawn. Results of simulations indicate that annual average ground-water withdrawal rates that range up to 16 million gallons per day (Mgal/d) can be withdrawn from the study area under simulated average hydrologic conditions depending on instream-flow criteria and water-supply demand patterns. Annual average withdrawals of 10 to 12 Mgal/d are possible for proposed demands of 3.4 Mgal/d in the Mishnock Basin, and for a constant annual instream-flow criterion of 0.5 cubic foot per second per square mile (ft3/s/mi2) at the four streamflow-constraint locations. An average withdrawal rate of 10 Mgal/d can meet estimates of future (2020) water-supply needs of surrounding communities in Rhode Island. This withdrawal rate represents about 13 percent of the average 2002 daily withdrawal from the Scituate Reservoir (76 Mgal/d), the State?s largest water supply. Average annual withdrawal rates of 6 to 7 Mgal/d are possible for more stringent instream-flow criteria that might be used during dry-period hydrologic conditions. Two example scenarios of dry-period instream-flow constraints were evaluated: first, a minimum instream flow of 0.1 cubic foot per second at any of the four constraint locations; and second, a minimum instream flow of 10 percent of the minimum monthly streamflow estimate for each streamflow-constraint location during the period 1961?2000. The State of Rhode Island is currently (2004) considering methods for establishing instream-flow criteria for streams within the State. Twelve alternative annual, seasonal, or monthly instream-flow criteria that have been or are being considered for application in southeastern New England were used as hypothetical constraints on maximum ground-water-withdrawal rates in management-model calculations. Maximum ground-water-withdrawal rates ranged from 5 to 16 Mgal/d under five alternative annual instream-flow criteria. Maximum ground-water-withdrawal rates ranged from 0 to 13.6 Mgal/d under seven alternative seasonal or monthly instream-flow criteria. The effect of ground-water withdrawals on seasonal variations in monthly average streamflows under each criterion also were compared. Evaluation of management-model results indicates that a single annual instream-flowcriterion may be sufficient to preserve seasonal variations in monthly average streamflows and meet water-supply demands in the Big River Area, because withdrawals from wells in the Big
Scientific Investigations Report↗
Rhode Island Water Supply System Management Plan Database (WSSMP-Version 1.0)
In Rhode Island, the availability of water of sufficient quality and quantity to meet current and future environmental and economic needs is vital to life and the State's economy. Water suppliers, the Rhode Island Water Resources Board (RIWRB), and other State agencies responsible for water resources in Rhode Island need information about available resources, the water-supply infrastructure, and water use patterns. These decision makers need historical, current, and future water-resource information. In 1997, the State of Rhode Island formalized a system of Water Supply System Management Plans (WSSMPs) to characterize and document relevant water-supply information. All major water suppliers (those that obtain, transport, purchase, or sell more than 50 million gallons of water per year) are required to prepare, maintain, and carry out WSSMPs. An electronic database for this WSSMP information has been deemed necessary by the RIWRB for water suppliers and State agencies to consistently document, maintain, and interpret the information in these plans. Availability of WSSMP data in standard formats will allow water suppliers and State agencies to improve the understanding of water-supply systems and to plan for future needs or water-supply emergencies. In 2002, however, the Rhode Island General Assembly passed a law that classifies some of the WSSMP information as confidential to protect the water-supply infrastructure from potential terrorist threats. Therefore the WSSMP database was designed for an implementation method that will balance security concerns with the information needs of the RIWRB, suppliers, other State agencies, and the public. A WSSMP database was developed by the U.S. Geological Survey in cooperation with the RIWRB. The database was designed to catalog WSSMP information in a format that would accommodate synthesis of current and future information about Rhode Island's water-supply infrastructure. This report documents the design and implementation of the WSSMP database. All WSSMP information in the database is, ultimately, linked to the individual water suppliers and to a WSSMP 'cycle' (which is currently a 5-year planning cycle for compiling WSSMP information). The database file contains 172 tables - 47 data tables, 61 association tables, 61 domain tables, and 3 example import-link tables. This database is currently implemented in the Microsoft Access database software because it is widely used within and outside of government and is familiar to many existing and potential customers. Design documentation facilitates current use and potential modification for future use of the database. Information within the structure of the WSSMP database file (WSSMPv01.mdb), a data dictionary file (WSSMPDD1.pdf), a detailed database-design diagram (WSSMPPL1.pdf), and this database-design report (OFR2004-1231.pdf) documents the design of the database. This report includes a discussion of each WSSMP data structure with an accompanying database-design diagram. Appendix 1 of this report is an index of the diagrams in the report and on the plate; this index is organized by table name in alphabetical order. Each of these products is included in digital format on the enclosed CD-ROM to facilitate use or modification of the database.
Open-File Report↗
Data Model and Relational Database Design for Highway Runoff Water-Quality Metadata
A National highway and urban runoff waterquality metadatabase was developed by the U.S. Geological Survey in cooperation with the Federal Highway Administration as part of the National Highway Runoff Water-Quality Data and Methodology Synthesis (NDAMS). The database was designed to catalog available literature and to document results of the synthesis in a format that would facilitate current and future research on highway and urban runoff. This report documents the design and implementation of the NDAMS relational database, which was designed to provide a catalog of available information and the results of an assessment of the available data. All the citations and the metadata collected during the review process are presented in a stratified metadatabase that contains citations for relevant publications, abstracts (or previa), and reportreview metadata for a sample of selected reports that document results of runoff quality investigations. The database is referred to as a metadatabase because it contains information about available data sets rather than a record of the original data. The database contains the metadata needed to evaluate and characterize how valid, current, complete, comparable, and technically defensible published and available information may be when evaluated for application to the different dataquality objectives as defined by decision makers. This database is a relational database, in that all information is ultimately linked to a given citation in the catalog of available reports. The main database file contains 86 tables consisting of 29 data tables, 11 association tables, and 46 domain tables. The data tables all link to a particular citation, and each data table is focused on one aspect of the information collected in the literature search and the evaluation of available information. This database is implemented in the Microsoft (MS) Access database software because it is widely used within and outside of government and is familiar to many existing and potential customers. The stratified metadatabase design for the NDAMS program is presented in the MS Access file DBDESIGN.mdb and documented with a data dictionary in the NDAMS_DD.mdb file recorded on the CD-ROM. The data dictionary file includes complete documentation of the table names, table descriptions, and information about each of the 419 fields in the database.
Open-File Report↗
A Synopsis of Technical Issues of Concern for Monitoring Trace Elements in Highway and Urban Runoff
Trace elements, which are regulated for aquatic life protection, are a primary concern in highway- and urban-runoff studies because stormwater runoff may transport these constituents from the land surface to receiving waters. Many of these trace elements are essential for biological activity and become detrimental only when geologic or anthropogenic sources exceed concentrations beyond ranges typical of the natural environment. The Federal Highway Administration and State Transportation Agencies are concerned about the potential effects of highway runoff on the watershed scale and for the management and protection of watersheds. Transportation agencies need information that is documented as valid, current, and scientifically defensible to support planning and management decisions. There are many technical issues of concern for monitoring trace elements; therefore, trace-element data commonly are considered suspect, and the responsibility to provide data-quality information to support the validity of reported results rests with the data-collection agency. Paved surfaces are fundamentally different physically, hydraulically, and chemically from the natural surfaces typical of most freshwater systems that have been the focus of many traceelement- monitoring studies. Existing scientific conceptions of the behavior of trace elements in the environment are based largely upon research on natural systems, rather than on systems typical of pavement runoff. Additionally, the logistics of stormwater sampling are difficult because of the great uncertainty in the occurrence and magnitude of storm events. Therefore, trace-element monitoring programs may be enhanced if monitoring and sampling programs are automated. Automation would standardize the process and provide a continuous record of the variations in flow and water-quality characteristics. Great care is required to collect and process samples in a manner that will minimize potential contamination or attenuation of trace elements and other sources of bias and variability in the sampling process. Trace elements have both natural and anthropogenic sources that may affect the sampling process, including the sample-collection and handling materials used in many trace-element monitoring studies. Trace elements also react with these materials within the timescales typical for collection, processing and analysis of runoff samples. To study the characteristics and potential effects of trace elements in highway and urban runoff, investigators typically sample one or more operationally defined matrixes including: whole water, dissolved (filtered water), suspended sediment, bottom sediment, biological tissue, and contaminant sources. The sampling and analysis of each of these sample matrixes can provide specific information about the occurrence and distribution of trace elements in runoff and receiving waters. There are, however, technical concerns specific to each matrix that must be understood and addressed through use of proper collection and processing protocols. Valid protocols are designed to minimize inherent problems and to maximize the accuracy, precision, comparability, and representativeness of data collected. Documentation, including information about monitoring protocols, quality assurance and quality control efforts, and ancillary data also is necessary to establish data quality. This documentation is especially important for evaluation of historical traceelement monitoring data, because trace-element monitoring protocols and analysis methods have been constantly changing over the past 30 years.
Open-File Report↗
Geographic Information for Analysis of Highway Runoff-Quality Data on a National or Regional Scale in the Conterminous United States
Spatial data are important for interpretation of water-quality information on a regional or national scale. Geographic information systems (GIS) facilitate interpretation and integration of spatial data. The geographic information and data compiled for the conterminous United States during the National Highway Runoff Water-Quality Data and Methodology Synthesis project is described in this document, which also includes information on the structure, file types, and the geographic information in the data files. This 'geodata' directory contains two subdirectories, labeled 'gisdata' and 'gisimage.' The 'gisdata' directory contains ArcInfo coverages, ArcInfo export files, shapefiles (used in ArcView), Spatial Data Transfer Standard Topological Vector Profile format files, and meta files in subdirectories organized by file type. The 'gisimage' directory contains the GIS data in common image-file formats. The spatial geodata includes two rain-zone region maps and a map of national ecosystems originally published by the U.S. Environmental Protection Agency; regional estimates of mean annual streamflow, and water hardness published by the Federal Highway Administration; and mean monthly temperature, mean annual precipitation, and mean monthly snowfall modified from data published by the National Climatic Data Center and made available to the public by the Oregon Climate Service at Oregon State University. These GIS files were compiled for qualitative spatial analysis of available data on a national and(or) regional scale and therefore should be considered as qualitative representations, not precise geographic location information.
Open-File Report↗
Chemical-Help Application for Classification and Identification of Stormwater Constituents
A computer application called Chemical Help was developed to facilitate review of reports for the National Highway Runoff Water-Quality Data and Methodology Synthesis (NDAMS). The application provides a tool to quickly find a proper classification for any constituent in the NDAMS review sheets. Chemical Help contents include the name of each water-quality property, constituent, or parameter, the section number within the NDAMS review sheet, the organizational levels within a classification hierarchy, the database number, and where appropriate, the chemical formula, the Chemical Abstract Service number, and a list of synonyms (for the organic chemicals). Therefore, Chemical Help provides information necessary to research available reference data for the water-quality properties and constituents of potential interest in stormwater studies. Chemical Help is implemented in the Microsoft help-system interface. (Computer files for the use and documentation of Chemical Help are included on an accompanying diskette.)
Open-File Report↗
Statistical Approaches to Interpretation of Local, Regional, and National Highway-Runoff and Urban-Stormwater Data
Decision makers need viable methods for the interpretation of local, regional, and national-highway runoff and urban-stormwater data including flows, concentrations and loads of chemical constituents and sediment, potential effects on receiving waters, and the potential effectiveness of various best management practices (BMPs). Valid (useful for intended purposes), current, and technically defensible stormwater-runoff models are needed to interpret data collected in field studies, to support existing highway and urban-runoffplanning processes, to meet National Pollutant Discharge Elimination System (NPDES) requirements, and to provide methods for computation of Total Maximum Daily Loads (TMDLs) systematically and economically. Historically, conceptual, simulation, empirical, and statistical models of varying levels of detail, complexity, and uncertainty have been used to meet various data-quality objectives in the decision-making processes necessary for the planning, design, construction, and maintenance of highways and for other land-use applications. Water-quality simulation models attempt a detailed representation of the physical processes and mechanisms at a given site. Empirical and statistical regional water-quality assessment models provide a more general picture of water quality or changes in water quality over a region. All these modeling techniques share one common aspect-their predictive ability is poor without suitable site-specific data for calibration. To properly apply the correct model, one must understand the classification of variables, the unique characteristics of water-resources data, and the concept of population structure and analysis. Classifying variables being used to analyze data may determine which statistical methods are appropriate for data analysis. An understanding of the characteristics of water-resources data is necessary to evaluate the applicability of different statistical methods, to interpret the results of these techniques, and to use tools and techniques that account for the unique nature of water-resources data sets. Populations of data on stormwater-runoff quantity and quality are often best modeled as logarithmic transformations. Therefore, these factors need to be considered to form valid, current, and technically defensible stormwater-runoff models. Regression analysis is an accepted method for interpretation of water-resources data and for prediction of current or future conditions at sites that fit the input data model. Regression analysis is designed to provide an estimate of the average response of a system as it relates to variation in one or more known variables. To produce valid models, however, regression analysis should include visual analysis of scatterplots, an examination of the regression equation, evaluation of the method design assumptions, and regression diagnostics. A number of statistical techniques are described in the text and in the appendixes to provide information necessary to interpret data by use of appropriate methods. Uncertainty is an important part of any decisionmaking process. In order to deal with uncertainty problems, the analyst needs to know the severity of the statistical uncertainty of the methods used to predict water quality. Statistical models need to be based on information that is meaningful, representative, complete, precise, accurate, and comparable to be deemed valid, up to date, and technically supportable. To assess uncertainty in the analytical tools, the modeling methods, and the underlying data set, all of these components need be documented and communicated in an accessible format within project publications.
Open-File Report↗
Assessing biological effects from highway-runoff constituents
Increased emphasis on evaluation of nonpoint-source pollution has intensified the need for techniques that can be used to discern the toxicological effects of complex chemical mixtures. In response, the use of biological assessment techniques is receiving increased regulatory emphasis. When applied with documented habitat assessment and chemical analysis, these techniques can increase our understanding of the influence of environmental contaminants on the biological integrity and ecological function of aquatic communities. The contaminants of greatest potential concern in highway runoff are those that arise from highway construction, maintenance, and use. The major contaminants of interest are deicers; nutrients; metals; petroleum-related organic compounds, such as polycyclic aromatic hydrocarbons (PAHs), benzene, toluene, ethylbenzene, and xylene (BTEX), and methyl tert -butyl ether (MTBE); sediment washed off the road surface; and agricultural chemicals used in highway maintenance. Hundreds, if not thousands, of biological endpoints (measurable responses of living organisms) may be either directly or associatively affected by contaminant exposure. Measurable effects can occur throughout ecosystem processes across the wide range of biological complexity, ranging from responses at the biochemical level to the community level. The challenge to the environmental scientist is to develop an understanding of the relationship of effects at various levels of biological organization in order to determine whether a causal relationship exists between chemical exposure and substantial ecological impairment. This report provides a brief history of the evolution of biological assessment techniques, a description of the major classes of contaminants that are of particular interest in highway runoff, an overview of representative biological assessment techniques, and a discussion of data-quality considerations. Published reports with a focus on the effects of highway runoff on the local ecosystem were reviewed to provide information on (1) the suitability of the existing data for a quantitative national synthesis, (2) the methods available to study the effects of highway runoff on local ecosystems, and (3) the potential for adverse effects on the roadside environment and receiving waters. Although many biological studies have been done, the use of different methods and a general lack of sufficient documentation precludes a quantitative national synthesis on the basis of the existing data. The Federal Highway Administration, the U.S. Environmental Protection Agency, the U.S. Geological Survey, the Intergovernmental Task Force on Monitoring Water Quality, and the National Resources Conservation Service all have developed and documented methods for assessing the effects of contaminants on ecosystems in receiving waters. These published methods can be used to formulate a set of protocols to provide consistent information from highway-runoff studies. Review of the literature indicates (qualitatively) that highway runoff (even from highways with high traffic volume) may not usually be acutely toxic. Tissue analysis and community assessments, however, indicate effects from highway- runoff sediments near discharge points (even from sites near highways with relatively low traffic volumes). At many sites, elevated concentrations of highway-runoff constituents were measured in tissues of species associated with aquatic sediments. Community assessments also indicate decreases in the diversity and productivity of aquatic ecosystems at some sites receiving highway runoff. These results are not definitive, however, and depend on many site-specific criteria that were not sufficiently documented in most of the studies reviewed.
Open-File Report↗
Basic Requirements for Collecting, Documenting, and Reporting Precipitation and Stormwater-Flow Measurements
Accurate and representative precipitation and stormwater-flow data are crucial for use of highway- or urban-runoff study results, either individually or in a regional or national synthesis of stormwater-runoff data. Equally important is information on the level of accuracy and representativeness of this precipitation and stormwaterflow data. Accurate and representative measurements of precipitation and stormwater flow, however, are difficult to obtain because of the rapidly changing spatial and temporal distribution of precipitation and flows during a storm. Many hydrologic and hydraulic factors must be considered in performing the following: selecting sites for measuring precipitation and stormwater flow that will provide data that adequately meet the objectives and goals of the study, determining frequencies and durations of data collection to fully characterize the storm and the rapidly changing stormwater flows, and selecting methods that will yield accurate data over the full range of both rainfall intensities and stormwater flows. To ensure that the accuracy and representativeness of precipitation and stormwater-flow data can be evaluated, decisions as to (1) where in the drainage system precipitation and stormwater flows are measured, (2) how frequently precipitation and stormwater flows are measured, (3) what methods are used to measure precipitation and stormwater flows, and (4) on what basis are these decisions made, must all be documented and communicated in an accessible format, such as a project description report, a data report or an appendix to a technical report, and (or) archived in a State or national records center. A quality assurance/quality control program must be established to ensure that this information is documented and reported, and that decisions made in the design phase of a study are continually reviewed, internally and externally, throughout the study. Without the supporting data needed to evaluate the accuracy and representativeness of the precipitation and stormwater-flow measurements, the data collected and interpretations made may have little meaning.
Open-File Report↗
Computer Program for Point Location And Calculation of ERror (PLACER)
A program designed for point location and calculation of error (PLACER) was developed as part of the Quality Assurance Program of the Federal Highway Administration/U.S. Geological Survey (USGS) National Data and Methodology Synthesis (NDAMS) review process. The program provides a standard method to derive study-site locations from site maps in highwayrunoff, urban-runoff, and other research reports. This report provides a guide for using PLACER, documents methods used to estimate study-site locations, documents the NDAMS Study-Site Locator Form, and documents the FORTRAN code used to implement the method. PLACER is a simple program that calculates the latitude and longitude coordinates of one or more study sites plotted on a published map and estimates the uncertainty of these calculated coordinates. PLACER calculates the latitude and longitude of each study site by interpolating between the coordinates of known features and the locations of study sites using any consistent, linear, user-defined coordinate system. This program will read data entered from the computer keyboard and(or) from a formatted text file, and will write the results to the computer screen and to a text file. PLACER is readily transferable to different computers and operating systems with few (if any) modifications because it is written in standard FORTRAN. PLACER can be used to calculate study site locations in latitude and longitude, using known map coordinates or features that are identifiable in geographic information data bases such as USGS Geographic Names Information System, which is available on the World Wide Web.
Open-File Report↗
Estimating Concentrations of Road-Salt Constituents in Highway-Runoff from Measurements of Specific Conductance
Discrete or composite samples of highway runoff may not adequately represent in-storm water-quality fluctuations because continuous records of water stage, specific conductance, pH, and temperature of the runoff indicate that these properties fluctuate substantially during a storm. Continuous records of water-quality properties can be used to maximize the information obtained about the stormwater runoff system being studied and can provide the context needed to interpret analyses of water samples. Concentrations of the road-salt constituents calcium, sodium, and chloride in highway runoff were estimated from theoretical and empirical relations between specific conductance and the concentrations of these ions. These relations were examined using the analysis of 233 highwayrunoff samples collected from August 1988 through March 1995 at four highway-drainage monitoring stations along State Route 25 in southeastern Massachusetts. Theoretically, the specific conductance of a water sample is the sum of the individual conductances attributed to each ionic species in solution-the product of the concentrations of each ion in milliequivalents per liter (meq/L) multiplied by the equivalent ionic conductance at infinite dilution-thereby establishing the principle of superposition. Superposition provides an estimate of actual specific conductance that is within measurement error throughout the conductance range of many natural waters, with errors of less than ?5 percent below 1,000 microsiemens per centimeter (?S/cm) and ?10 percent between 1,000 and 4,000 ?S/cm if all major ionic constituents are accounted for. A semi-empirical method (adjusted superposition) was used to adjust for concentration effects-superposition-method prediction errors at high and low concentrations-and to relate measured specific conductance to that calculated using superposition. The adjusted superposition method, which was developed to interpret the State Route 25 highway-runoff records, accounts for contributions of constituents other than calcium, sodium, and chloride in dilute waters. The adjusted superposition method also accounts for the attenuation of each constituent's contribution to conductance as ionic strength increases. Use of the adjusted superposition method generally reduced predictive error to within measurement error throughout the range of specific conductance (from 37 to 51,500 ?S/cm) in the highway runoff samples. The effects of pH, temperature, and organic constituents on the relation between concentrations of dissolved constituents and measured specific conductance were examined but these properties did not substantially affect interpretation of the Route 25 data set. Predictive abilities of the adjusted superposition method were similar to results obtained by standard regression techniques, but the adjusted superposition method has several advantages. Adjusted superposition can be applied using available published data about the constituents in precipitation, highway runoff, and the deicing chemicals applied to a highway. This semi-empirical method can be used as a predictive and diagnostic tool before a substantial number of samples are collected, but the power of the regression method is based upon a large number of water-quality analyses that may be affected by a bias in the data.
Water-Resources Investigations Report↗
Technology Transfer Opportunities: Automated Ground-Water Monitoring, A Proven Technology
Introduction The U.S. Geological Survey (USGS) has developed and tested an automated ground-water monitoring system that measures and records values of selected water-quality properties and constituents using protocols approved for manual sampling. Prototypes using the automated process have demonstrated the ability to increase the quantity and quality of data collected and have shown the potential for reducing labor and material costs for ground-water quality data collection. Automated ground-water monitoring systems can be used to monitor known or potential contaminant sites, such as near landfills, underground storage tanks, or other facilities where potential contaminants are stored, to serve as early warning systems monitoring ground-water quality near public water-supply wells, and for ground-water quality research.
Fact Sheet↗
Data Quality Objectives and Criteria for Basic Information, Acceptable Uncertainty, and Quality-Assurance and Quality-Control Documentation
The Federal Highway Administration and State transportation agencies have the responsibility of determining and minimizing the effects of highway runoff on water quality; therefore, they have been conducting an extensive program of water-quality monitoring and research during the last 25 years. The objectives and monitoring goals of highway runoff studies have been diverse, because the highway community must address many different questions about the characteristics and impacts of highway runoff. The Federal Highway Administration must establish that available data and procedures that are used to assess and predict pollutant loadings and impacts from highway stormwater runoff are valid, current, and technically supportable. This report examines criteria for evaluating water-quality data and resultant interpretations. The criteria used to determine if data are valid (useful for intended purposes), current, and technically supportable are derived from published materials from the Federal Highway Administration, the U.S. Environmental Protection Agency, the Intergovernmental Task Force on Monitoring Water Quality, the U.S. Geological Survey and from technical experts throughout the U.S. Geological Survey. Water-quality data that are documented to be meaningful, representative, complete, precise, accurate, comparable, and admissible as legal evidence will meet the scientific, engineering, and regulatory needs of highway agencies. Documentation of basic information, such as compatible monitoring objectives and program design features; metadata (when, where, and how data were collected as well as who collected and analyzed the data); ancillary information (explanatory variables and study-site characteristics); and legal requirements are needed to evaluate data. Documentation of sufficient quality-assurance and quality-control information to establish the quality and uncertainty in the data and interpretations also are needed to determine the comparability and utility of data sets for intended uses. The fact that a program's data may not meet screening criteria for a national synthesis does not mean that the data are not useful for meeting that program's objectives or that they could not be used for water-quality studies with different objectives.
Open-File Report↗
Technology Transfer Opportunities: Automated Ground-Water Monitoring
Introduction A new automated ground-water monitoring system developed by the U.S. Geological Survey (USGS) measures and records values of selected water-quality properties and constituents using protocols approved for manual sampling. Prototypes using the automated process have demonstrated the ability to increase the quantity and quality of data collected and have shown the potential for reducing labor and material costs for ground-water quality data collection. Automation of water-quality monitoring systems in the field, in laboratories, and in industry have increased data density and utility while reducing operating costs. Uses for an automated ground-water monitoring system include, (but are not limited to) monitoring ground-water quality for research, monitoring known or potential contaminant sites, such as near landfills, underground storage tanks, or other facilities where potential contaminants are stored, and as an early warning system monitoring groundwater quality near public water-supply wells.
Fact Sheet↗
Mobilization of major and trace constituents of highway runoff in groundwater potentially caused by deicing chemical migration
The quality of water in unsaturated zones and groundwater is affected by the major ions in deicing chemicals applied to roads and highways. The assessment of the environmental effects of highway runoff requires investigations to determine whether other major and trace constituents are mobilized during deicing chemical migration through the unsaturated zone and groundwater. In this regard, groundwater samples were analyzed in February and August 1991, and March, August, and November 1993 at a test site along Route 25 in southeastern Massachusetts. Analyses indicated that concentrations of major and trace chemical constituents of highway runoff in groundwater are substantially higher downgradient than upgradient from the highway.
Transportation Research Record↗