Geology topics

Gregory C. McLaskey

Publications and source records attributed to Gregory C. McLaskey.

9 recordsLinked to original sources

USGS2026

Fully contained laboratory earthquakes: The effect of asperity aspect ratio and free surfaces

Corner frequency ( f c ) and seismic moment ( M 0 ) are key parameters derived from seismic signals that are used to characterize earthquake stress drop, rupture area, and slip. These parameters are also affected by fault geometry and boundary conditions. However, the systematic study of these effects in laboratory settings has been challenging. This study presents laboratory earthquake experiments that examine how rupture dynamics are influenced by (a) the aspect ratio of rectangular PMMA velocity-weakening (VW) asperities surrounded by the Teflon velocity-strengthening (VS) patches, and (b) whether the sides of a VW asperity are confined with VS patches or are free surfaces. We found that increasing confinement by reducing free surfaces or increasing the VW asperity aspect ratio stabilizes fault slip, so that higher normal stress is required to transition from aseismic to seismic slip. Increased confinement and high aspect ratios also reduced M 0 and increased f c , both of which were determined from the radiated seismic waves. M 0 and f c were primarily controlled by the shorter dimension of the VW asperity. Analysis of high-frequency acoustic emission signals revealed that ruptures on high-aspect-ratio VW asperities propagated more unidirectionally, whereas ruptures on square VW asperities were more complex. Further, the high-aspect-ratio asperities were more likely to be eroded by surrounding VS regions while low-aspect-ratio asperities were more likely to rupture into the VS surroundings. These results demonstrate that both the confinement from surrounding stable areas and the geometry of the seismogenic patch can affect rupture nucleation, propagation, and seismic source characteristics.

JGR Solid Earth↗

USGS2018

Shear failure of a granite pin traversing a sawcut fault

Fault heterogeneities such as bumps, bends, and stepovers are commonly observed on natural faults, but are challenging to recreate under controlled laboratory conditions. We study deformation and microseismicity of a 76 mm-diameter Westerly granite cylinder with a sawcut fault with known frictional properties. An idealized asperity is added by emplacing a precision-ground 21 mm-diameter solid granite dowel that crosses the center of the fault at right angles. This intact granite ‘pin’ provides a strength contrast that resists fault slip. Upon loading to 80 MPa in a triaxial machine, we first observed a M -4 slip event that ruptured the sawcut fault, slipped 40 µm, but was halted by the granite pin. With continued loading, the pin failed in a swarm of thousands of M -6 to M -8 events known as acoustic emissions (AEs). Once the pin was fractured to a critical point, it permitted complete rupture events (M -3) on the sawcut fault (stick-slip instabilities). Subsequent slip events were preceded by clusters of foreshock-like AEs, all located on the fault plane, and the spatial extent of the foreshock clusters is consistent with our estimate of a critical nucleation dimension h*. We also identified an aseismic zone on the fault plane surrounding the fractured rock pin. A post-mortem analysis of the sample showed a thick gouge layer where the pin intersected the fault, suggesting that dilatancy of this gouge propped open the fault and prevented microseismic events in its vicinity. Recorded microseismicity separates into three categories: slip on the sawcut fault, fracture of the intact rock pin, and off-fault seismicity associated with pin-related rock joints. We found that pin fracture events were exclusively implosive (anticrack) even though the shear process zone was overall dilatant. This shows how aseismic effects can lead to unexpected seismic manifestations of certain faulting processes.

International Journal of Rock Mechanics and Mining↗

USGS2016

Calibrated acoustic emission system records M -3.5 to M -8 events generated on a saw-cut granite sample

Acoustic emission (AE) analyses have been used for decades for rock mechanics testing, but because AE systems are not typically calibrated, the absolute sizes of dynamic microcrack growth and other physical processes responsible for the generation of AEs are poorly constrained. We describe a calibration technique for the AE recording system as a whole (transducers + amplifiers + digitizers + sample + loading frame) that uses the impact of a 4.76-mm free-falling steel ball bearing as a reference source. We demonstrate the technique on a 76-mm diameter cylinder of westerly granite loaded in a triaxial deformation apparatus at 40 MPa confining pressure. The ball bearing is dropped inside a cavity within the sample while inside the pressure vessel. We compare this reference source to conventional AEs generated during loading of a saw-cut fault in a second granite sample. All located AEs occur on the saw-cut surface and have moment magnitudes ranging from M −5.7 down to at least M −8. Dynamic events rupturing the entire simulated fault surface (stick–slip events) have measurable stress drop and macroscopic slip and radiate seismic waves similar to those from a M −3.5 earthquake. The largest AE events that do not rupture the entire fault are M −5.7. For these events, we also estimate the corner frequency (200–300 kHz), and we assume the Brune model to estimate source dimensions of 4–6 mm. These AE sources are larger than the 0.2 mm grain size and smaller than the 76 × 152 mm fault surface.

Rock Mechanics and Rock Engineering↗

USGS2015

Slip-pulse rupture behavior on a 2 meter granite fault

We describe observations of dynamic rupture events that spontaneously arise on meter-scale laboratory earthquake experiments. While low-frequency slip of the granite sample occurs in a relatively uniform and crack-like manner, instruments capable of detecting high frequency motions show that some parts of the fault slip abruptly (velocity >100 mm∙s-1, acceleration >20 km∙s-2) while the majority of the fault slips more slowly. Abruptly slipping regions propagate along the fault at nearly the shear wave speed. We propose that the dramatic reduction in frictional strength implied by this pulse-like rupture behavior has a common mechanism to the weakening reported in high velocity friction experiments performed on rotary machines. The slip pulses can also be identified as migrating sources of high frequency seismic waves. As observations from large earthquakes show similar propagating high frequency sources, the pulses described here may have relevance to the mechanics of larger earthquakes.

Geophysical Research Letters↗

USGS2015

A robust calibration technique for acoustic emission systems based on momentum transfer from a ball drop

We describe a technique to estimate the seismic moment of acoustic emissions and other extremely small seismic events. Unlike previous calibration techniques, it does not require modeling of the wave propagation, sensor response, or signal conditioning. Rather, this technique calibrates the recording system as a whole and uses a ball impact as a reference source or empirical Green’s function. To correctly apply this technique, we develop mathematical expressions that link the seismic moment $M_{0}$ of internal seismic sources (i.e., earthquakes and acoustic emissions) to the impulse, or change in momentum $\Delta p $, of externally applied seismic sources (i.e., meteor impacts or, in this case, ball impact). We find that, at low frequencies, moment and impulse are linked by a constant, which we call the force‐moment‐rate scale factor $C_{F\dot{M}} = M_{0}/\Delta p$. This constant is equal to twice the speed of sound in the material from which the seismic sources were generated. Next, we demonstrate the calibration technique on two different experimental rock mechanics facilities. The first example is a saw‐cut cylindrical granite sample that is loaded in a triaxial apparatus at 40 MPa confining pressure. The second example is a 2 m long fault cut in a granite sample and deformed in a large biaxial apparatus at lower stress levels. Using the empirical calibration technique, we are able to determine absolute source parameters including the seismic moment, corner frequency, stress drop, and radiated energy of these magnitude −2.5 to −7 seismic events.

Bulletin of the Seismological Society of America↗

USGS2014

Laboratory generated M -6 earthquakes

We consider whether mm-scale earthquake-like seismic events generated in laboratory experiments are consistent with our understanding of the physics of larger earthquakes. This work focuses on a population of 48 very small shocks that are foreshocks and aftershocks of stick–slip events occurring on a 2.0 m by 0.4 m simulated strike-slip fault cut through a large granite sample. Unlike the larger stick–slip events that rupture the entirety of the simulated fault, the small foreshocks and aftershocks are contained events whose properties are controlled by the rigidity of the surrounding granite blocks rather than characteristics of the experimental apparatus. The large size of the experimental apparatus, high fidelity sensors, rigorous treatment of wave propagation effects, and in situ system calibration separates this study from traditional acoustic emission analyses and allows these sources to be studied with as much rigor as larger natural earthquakes. The tiny events have short (3–6 μs) rise times and are well modeled by simple double couple focal mechanisms that are consistent with left-lateral slip occurring on a mm-scale patch of the precut fault surface. The repeatability of the experiments indicates that they are the result of frictional processes on the simulated fault surface rather than grain crushing or fracture of fresh rock. Our waveform analysis shows no significant differences (other than size) between the M -7 to M -5.5 earthquakes reported here and larger natural earthquakes. Their source characteristics such as stress drop (1–10 MPa) appear to be entirely consistent with earthquake scaling laws derived for larger earthquakes.

Pure and Applied Geophysics↗

USGS2014

Preslip and cascade processes initiating laboratory stick slip

Recent modeling studies have explored whether earthquakes begin with a large aseismic nucleation process or initiate dynamically from the rapid growth of a smaller instability in a “cascade-up” process. To explore such a case in the laboratory, we study the initiation of dynamic rupture (stick slip) of a smooth saw-cut fault in a 76mm diameter cylindrical granite laboratory sample at 40–120MPa confining pressure. We use a high dynamic range recording system to directly compare the seismic waves radiated during the stick-slip event to those radiated from tiny (M _6) discrete seismic events, commonly known as acoustic emissions (AEs), that occur in the seconds prior to each large stick slip. The seismic moments, focal mechanisms, locations, and timing of the AEs all contribute to our understanding of their mechanics and provide us with information about the stick-slip nucleation process. In a sequence of 10 stick slips, the first few microseconds of the signals recorded from stick-slip instabilities are nearly indistinguishable from those of premonitory AEs. In this sense, it appears that each stick slip begins as an AE event that rapidly (~20 μs) grows about 2 orders of magnitude in linear dimension and ruptures the entire 150mm length of the simulated fault. We also measure accelerating fault slip in the final seconds before stick slip. We estimate that this slip is at least 98% aseismic and that it both weakens the fault and produces AEs that will eventually cascade-up to initiate the larger dynamic rupture.

Journal of Geophysical Research B: Solid Earth↗

USGS2013

Foreshocks during the nucleation of stick-slip instability

We report on laboratory experiments which investigate interactions between aseismic slip, stress changes, and seismicity on a critically stressed fault during the nucleation of stick-slip instability. We monitor quasi-static and dynamic changes in local shear stress and fault slip with arrays of gages deployed along a simulated strike-slip fault (2 m long and 0.4 m deep) in a saw cut sample of Sierra White granite. With 14 piezoelectric sensors, we simultaneously monitor seismic signals produced during the nucleation phase and subsequent dynamic rupture. We observe localized aseismic fault slip in an approximately meter-sized zone in the center of the fault, while the ends of the fault remain locked. Clusters of high-frequency foreshocks (M w ~ −6.5 to −5.0) can occur in this slowly slipping zone 5–50 ms prior to the initiation of dynamic rupture; their occurrence appears to be dependent on the rate at which local shear stress is applied to the fault. The meter-sized nucleation zone is generally consistent with theoretical estimates, but source radii of the foreshocks (2 to 70 mm) are 1 to 2 orders of magnitude smaller than the theoretical minimum length scale over which earthquake nucleation can occur. We propose that frictional stability and the transition between seismic and aseismic slip are modulated by local stressing rate and that fault sections, which would typically slip aseismically, may radiate seismic waves if they are rapidly stressed. Fault behavior of this type may provide physical insight into the mechanics of foreshocks, tremor, repeating earthquake sequences, and a minimum earthquake source dimension.

Journal of Geophysical Research B: Solid Earth↗

USGS2012

Fault healing promotes high-frequency earthquakes in laboratory experiments and on natural faults

Faults strengthen or heal with time in stationary contact and this healing may be an essential ingredient for the generation of earthquakes. In the laboratory, healing is thought to be the result of thermally activated mechanisms that weld together micrometre-sized asperity contacts on the fault surface, but the relationship between laboratory measures of fault healing and the seismically observable properties of earthquakes is at present not well defined. Here we report on laboratory experiments and seismological observations that show how the spectral properties of earthquakes vary as a function of fault healing time. In the laboratory, we find that increased healing causes a disproportionately large amount of high-frequency seismic radiation to be produced during fault rupture. We observe a similar connection between earthquake spectra and recurrence time for repeating earthquake sequences on natural faults. Healing rates depend on pressure, temperature and mineralogy, so the connection between seismicity and healing may help to explain recent observations of large megathrust earthquakes which indicate that energetic, high-frequency seismic radiation originates from locations that are distinct from the geodetically inferred locations of large-amplitude fault slip

Nature↗