Search USGSSearch

Geology topics

Edwin L. Harp

Publications and source records attributed to Edwin L. Harp.

At least 19 recordsLinked to original sources

Map of landslides triggered by the January 12, 2010, Haiti earthquake

The magnitude (M) 7.0 Haiti earthquake of January 12, 2010, triggered landslides throughout much of Haiti on the island of Hispaniola in the Caribbean Sea. The epicenter of the quake was located at 18.44°N., 72.57°W. at a depth of 13 kilometers (km) approximately 25 km southwest of the capital, Port-au-Prince. Although estimates vary widely, the most reliable surveys of casualties indicate that the earthquake caused 158,679 fatalities and more than 300,000 injuries. The U.S. Geological Survey compared publicly available satellite imagery acquired both before and after the earthquake and mapped 23,567 landslides that were triggered by the strong shaking. Our mapping from aerial photography and satellite imagery was augmented by field observations. Most of the landslides triggered by the earthquake were south of the Léogâne fault on the footwall and were fairly shallow falls and slides in weathered limestone (2–5 meters [m] thick) and volcanic rock and soil (generally <1 m thick). Landslides extended from the north to the south coasts of the southwestern peninsula (southwest of Port-au-Prince) and almost 60 km to the east and west of the epicenter. The highest concentration of landslides was on the steep limestone slopes of incised river valleys, but large numbers of landslides also occurred on gentler slopes in weathered volcanic rocks. Although some high landslide concentrations did occur near areas of maximum fault slip, the overall distribution of landslides appears to involve complex interactions between geology, topography, and strong shaking with limited spatial correlation between fault slip and landslides.

Scientific Investigations Map

Ground motions at the outermost limits of seismically triggered landslides

Over the last few decades, we and our colleagues have conducted field investigations in which we mapped the outermost limits of triggered landslides in four earthquakes: 1987 Whittier Narrows, California ( M 5.9), 1987 Superstition Hills, California ( M 6.5), 1994 Northridge, California ( M 6.7), and 2011 Mineral, Virginia ( M 5.8). In an additional two earthquakes, 1976 Guatemala ( M 7.5) and 1983 Coalinga, California ( M 6.5), we determined limits using high‐resolution aerial‐photographic interpretation in conjunction with more limited ground investigation. Limits in these earthquakes were defined by the locations of the very smallest failures (<1&thinsp;&thinsp;m 3 ) from the most susceptible slopes that can be identified positively as having been triggered by earthquake shaking. Because we and our colleagues conducted all of these investigations, consistent methodology and criteria were used in determining limits. In the six earthquakes examined, we correlated the outermost landslide limits with peak ground accelerations (PGAs) from ShakeMap models of each earthquake. For the four earthquakes studied by field investigation, the minimum PGA values associated with farthest landslide limits ranged from 0.02 g to 0.08 g . The range for the two earthquakes investigated using aerial‐photographic interpretations was 0.05&ndash;0.11 g . Although PGA values at landslide limits depend on several factors, including material strength, topographic amplification, and hydrologic conditions, these values provide an empirically useful lower limiting range of PGA needed to trigger the smallest failures on very susceptible slopes. In a well‐recorded earthquake, this PGA range can be used to identify an outer boundary within which we might expect to find landsliding; in earthquakes that are not well recorded, mapping the outermost landslide limits provides a useful clue about ground‐motion levels at the mapped limits.

Bulletin of the Seismological Society of America

Relation of landslides triggered by the Kiholo Bay earthquake to modeled ground motion

The 2006 Kiholo Bay, Hawaii, earthquake triggered high concentrations of rock falls and slides in the steep canyons of the Kohala Mountains along the north coast of Hawaii. Within these mountains and canyons a complex distribution of landslides was triggered by the earthquake shaking. In parts of the area, landslides were preferentially located on east‐facing slopes, whereas in other parts of the canyons no systematic pattern prevailed with respect to slope aspect or vertical position on the slopes. The geology within the canyons is homogeneous, so we hypothesize that the variable landslide distribution is the result of localized variation in ground shaking; therefore, we used a state‐of‐the‐art, high‐resolution ground‐motion simulation model to see if it could reproduce the landslide‐distribution patterns. We used a 3D finite‐element analysis to model earthquake shaking using a 10 m digital elevation model and slip on a finite‐fault model constructed from teleseismic records of the mainshock. Ground velocity time histories were calculated up to a frequency of 5 Hz. Dynamic shear strain also was calculated and compared with the landslide distribution. Results were mixed for the velocity simulations, with some areas showing correlation of landslide locations with peak modeled ground motions but many other areas showing no such correlation. Results were much improved for the comparison with dynamic shear strain. This suggests that (1) rock falls and slides are possibly triggered by higher frequency ground motions (velocities) than those in our simulations, (2) the ground‐motion velocity model needs more refinement, or (3) dynamic shear strain may be a more fundamental measurement of the decoupling process of slope materials during seismic shaking.

Hawai'i

Landslides in the northern Colorado Front Range caused by rainfall, September 11-13, 2013

During the second week of September 2013, nearly continuous rainfall caused widespread landslides and flooding in the northern Colorado Front Range. The combination of landslides and flooding was responsible for eight fatalities and caused extensive damage to buildings, highways, and infrastructure. Three fatalities were attributed to a fast moving type of landslide called debris flow. One fatality occurred in Jamestown, and two occurred in the community of Pinebrook Hills immediately west of the City of Boulder. All major canyon roads in the northern Front Range were periodically closed between September 11 and 13, 2013. Some canyon closures were caused by undercutting of roads by landslides and flooding, and some were caused by debris flows and rock slides that deposited material on road surfaces. Most of the canyon roads, with the exceptions of U.S. Highway 6 (Clear Creek Canyon), State Highway 46/Jefferson Co. Rd. 70 (Golden Gate Canyon), and Sunshine Canyon in Boulder County, remained closed at the end of September 2013. A review of historical records in Colorado indicates that this type of event, with widespread landslides and flooding occurring over a very large region, in such a short period of time, is rare.

Colorado

Quantitative rock-fall hazard and risk assessment for Yosemite Valley, Yosemite National Park, California

Rock falls are common in Yosemite Valley, California, posing substantial hazard and risk to the approximately four million annual visitors to Yosemite National Park. Rock falls in Yosemite Valley over the past few decades have damaged structures and caused injuries within developed regions located on or adjacent to talus slopes highlighting the need for additional investigations into rock-fall hazard and risk. This assessment builds upon previous investigations of rock-fall hazard and risk in Yosemite Valley and focuses on hazard and risk to structures posed by relatively frequent fragmental-type rock falls as large as approximately 100,000 (cubic meters) in volume.

California

The effect of complex fault rupture on the distribution of landslides triggered by the 12 January 2010, Haiti earthquake

The M W 7.0, 12 January 2010, Haiti earthquake triggered more than 7,000 landslides in the mountainous terrain south of Port-au-Prince over an area that extends approximately 50 km to the east and west from the epicenter and to the southern coast. Most of the triggered landslides were rock and soil slides from 25°–65° slopes within heavily fractured limestone and deeply weathered basalt and basaltic breccia. Landslide volumes ranged from tens of cubic meters to several thousand cubic meters. Rock slides in limestone typically were 2–5 m thick; slides within soils and weathered basalt typically were less than 1 m thick. Twenty to thirty larger landslides having volumes greater than 10,000 m 3 were triggered by the earthquake; these included block slides and rotational slumps in limestone bedrock. Only a few landslides larger than 5,000 m 3 occurred in the weathered basalt. The distribution of landslides is asymmetric with respect to the fault source and epicenter. Relatively few landslides were triggered north of the fault source on the hanging wall. The densest landslide concentrations lie south of the fault source and the Enriquillo-Plantain-Garden fault zone on the footwall. Numerous landslides also occurred along the south coast west of Jacmél. This asymmetric distribution of landsliding with respect to the fault source is unusual given the modeled displacement of the fault source as mainly thrust motion to the south on a plane dipping to the north at approximately 55°; landslide concentrations in other documented thrust earthquakes generally have been greatest on the hanging wall. This apparent inconsistency of the landslide distribution with respect to the fault model remains poorly understood given the lack of any strong-motion instruments within Haiti during the earthquake.

Book chapter

Extraordinary distance limits of landslides triggered by the 2011 Mineral, Virginia, earthquake

The 23 August 2011 Mineral, Virginia, earthquake (M w 5.8) was the largest to strike the eastern U.S. since 1897 and was felt over an extraordinarily large area. Although no large landslides occurred, the shaking did trigger many rock and soil falls from steep river banks and natural cliffs in the epicentral area and from steep road cuts along, and northwest of, the Blue Ridge Parkway. We mapped the occurrence of rock falls to determine distance limits that could be compared with those from other documented earthquakes. Studies of previous earthquakes indicated a maximum epicentral distance limit for landsliding of ~60 km for an M 5.8 earthquake; the maximum distance limit for the 2011 earthquake was 245 km, the largest exceedance of the historical limit ever recorded. Likewise, the previous maximum area affected by landslides for this magnitude was 1500 km 2 ; the area affected by landslides in the 2011 earthquake was 33,400 km 2 . These observations provide physical evidence that attenuation of strong shaking for eastern U.S. earthquakes is significantly lower than for plate‐boundary earthquakes. Also, distance limits parallel to the regional structural trend are greater than those that transect the structure, which suggests anisotropic attenuation related to the regional geologic structure. Peak ground acceleration (PGA) at the landslide distance limits is estimated to have been about 0.02–0.04g.

Virginia

Progressive failure of sheeted rock slopes: the 2009–2010 Rhombus Wall rock falls in Yosemite Valley, California, USA

Progressive rock-fall failures in natural rock slopes are common in many environments, but often elude detailed quantitative documentation and analysis. Here we present high-resolution photography, video, and laser scanning data that document spatial and temporal patterns of a 15-month-long sequence of at least 14 rock falls from the Rhombus Wall, a sheeted granitic cliff in Yosemite Valley, California. The rock-fall sequence began on 26 August 2009 with a small failure at the tip of an overhanging rock slab. Several hours later, a series of five rock falls totaling 736 m 3 progressed upward along a sheeting joint behind the overhanging slab. Over the next 3 weeks, audible cracking occurred on the Rhombus Wall, suggesting crack propagation, while visual monitoring revealed opening of a sheeting joint adjacent to the previous failure surface. On 14 September 2009 a 110 m 3 slab detached along this sheeting joint. Additional rock falls between 30 August and 20 November 2010, totaling 187 m 3 , radiated outward from the initial failure area along cliff (sub)parallel sheeting joints. We suggest that these progressive failures might have been related to stress redistributions accompanying propagation of sheeting joints behind the cliff face. Mechanical analyses indicate that tensile stresses should occur perpendicular to the cliff face and open sheeting joints, and that sheeting joints should propagate parallel to a cliff face from areas of stress concentrations. The analyses also account for how sheeting joints can propagate to lengths many times greater than their depths behind cliff faces. We posit that as a region of failure spreads across a cliff face, stress concentrations along its margin will spread with it, promoting further crack propagation and rock falls.

California

Rock fall simulation at Timpanogos Cave National Monument, American Fork Canyon, Utah, USA

Rock fall from limestone cliffs at Timpanogos Cave National Monument in American Fork Canyon east of Provo, Utah, is a common occurrence. The cave is located in limestone cliffs high on the southern side of the canyon. One fatality in 1933 led to the construction of rock fall shelters at the cave entrance and exit in 1976. Numerous rock fall incidents, including a near miss in 2000 in the vicinity of the trail below the cave exit, have led to a decision to extend the shelter at the cave exit to protect visitors from these ongoing rock fall events initiating from cliffs immediately above the cave exit. Three-dimensional rock fall simulations from sources at the top of these cliffs have provided data from which to assess the spatial frequencies and velocities of rock falls from the cliffs and to constrain the design of protective measures to reduce the rock fall hazard. Results from the rock fall simulations are consistent with the spatial patterns of rock fall impacts that have been observed at the cave exit site.

Utah

Shallow landslide hazard map of Seattle, Washington

Landslides, particularly debris flows, have long been a significant cause of damage and destruction to people and property in the Puget Sound region. Following the years of 1996 and 1997, the Federal Emergency Management Agency designated Seattle as a &ldquo;Project Impact&rdquo; city with the goal of encouraging the city to become more disaster resistant to landslides and other natural hazards. A major recommendation of the Project Impact council was that the city and the U.S. Geological Survey collaborate to produce a landslide hazard map. An exceptional data set archived by the city containing more than 100 yr of landslide data from severe storm events allowed comparison of actual landslide locations with those predicted by slope-stability modeling. We used an infinite-slope analysis, which models slope segments as rigid friction blocks, to estimate the susceptibility of slopes to debris flows, which are water-laden slurries that can form from shallow failures of soil and weathered bedrock and can travel at high velocities down steep slopes. Data used for the analysis consisted of a digital slope map derived from recent light detection and ranging (LiDAR) imagery of Seattle, recent digital geologic mapping of the city, and shear-strength test data for the geologic units found in the surrounding area. The combination of these data layers within a geographic information system (GIS) platform allowed us to create a shallow landslide hazard map for Seattle.

Washington

Landslide and Land Subsidence Hazards to Pipelines

Landslides and land subsidence pose serious hazards to pipelines throughout the world. Many existing pipeline corridors and more and more new pipelines cross terrain that is affected by either landslides, land subsidence, or both. Consequently the pipeline industry recognizes a need for increased awareness of methods for identifying and evaluating landslide and subsidence hazard for pipeline corridors. This report was prepared in cooperation with the U.S. Department of Transportation Pipeline and Hazardous Materials Safety Administration, and Pipeline Research Council International through a cooperative research and development agreement (CRADA) with DGH Consulting, Inc., to address the need for up-to-date information about current methods to identify and assess these hazards. Chapters in this report (1) describe methods for evaluating landslide hazard on a regional basis, (2) describe the various types of land subsidence hazard in the United States and available methods for identifying and quantifying subsidence, and (3) summarize current methods for investigating individual landslides. In addition to the descriptions, this report provides information about the relative costs, limitations and reliability of various methods.

Open-File Report

Ferguson rock slide buries California State Highway near Yosemite National Park

During spring 2006, talus from the toe area of a rock-block slide of about 800,000 m 3 buried California State Highway 140, one of the main routes into heavily-visited Yosemite National Park, USA. Closure of the highway for 92 days caused business losses of about 4.8 million USD. The rock slide, composed of slate and phyllite, moved slowly downslope from April to June 2006, creating a fresh head scarp with 9-12 m of displacement. Movement of the main rock slide, a re-activation of an older slide, was triggered by an exceptionally wet spring 2006, following a very wet spring 2005. As of autumn 2006, most of the main slide appeared to be at rest, although rocks occasionally continued to fall from steep, fractured rock masses at the toe area of the slide. Future behavior of the slide is difficult to predict, but possible scenarios range from continued scattered rock fall to complete rapid failure of the entire mass. Although unlikely except under very destabilizing circumstances, a worst-case, rapid failure of the entire rock slide could extend across the Merced River, damming the river and creating a reservoir. As a temporary measure, traffic has been rerouted to the opposite side of the Merced River at about the same elevation as the buried section of Highway 140. A state-of-the-art monitoring system has been installed to detect movement in the steep talus slope, movement of the main slide mass, local strong ground motion from regional earthquakes, and sudden changes in stream levels, possibly indicating damming of the river by slide material.

California

Landslides triggered by the October 8, 2005, Pakistan earthquake and associated landslide-dammed reservoirs

The October 8, 2005, Kashmir earthquake (M 7.6) triggered several thousand landslides, mainly rock falls and rock slides, in the epicentral area near the cities of Muzafarrabad and Balakot, Pakistan. Most of these were shallow, coalescing rock slides emanating from highly sheared and deformed limestone and dolomite of the Precambrian Muzafarrabad Formation. The largest landslide triggered by the earthquake is located approximately 32 kilometers southeast of Muzafarrabad in a tributary valley of the Jhelum River. This landslide is a debris avalanche of approximately 80 million cubic meters volume within the Miocene Murree Formation consisting of mixed sandstone, mudstone, shale, and limestone. The avalanche buried the village of Dandbeh and resulted in approximately 1,000 fatalities, according to local residents. The avalanche deposit traveled approximately 1.5 kilometers downslope and 300 meters or more up the opposite slope in the adjacent Karli stream drainage and also extended into the Tang stream drainage where the Tang stream joins the Karli drainage. The landslide mass has impounded two lakes within the blocked drainages. The lake in the Karli drainage was approximately 800 meters long and 20 meters deep as of December 19, 2005. The lake in the Tang drainage was approximately 400 meters long and 10 meters deep as of this same date. Downstream populations are at risk from possible flash flooding when these debris dams are overtopped by the reservoir water. The closest village, Hattian, is 2.8 kilometers downstream at the junction of the Jhelum River and the landslide-dammed Karli tributary. Other populations along the Jhelum River may also be at risk. Pakistan military engineers are preparing to construct a spillway within the landslide deposits to lessen the severity of the flood if the lake in the Karli stream drainage breaches the landslide dam catastrophically.

Open-File Report

Stability of leaning column at Devils Tower National Monument, Wyoming

In response to reports from climbers that an 8-meter section (referred to as the leaning column) of the most popular climbing route on Devils Tower in northeastern Wyoming is now moving when being climbed, scientists from the U.S. Geological Survey inspected the site to determine the stability of the column and the underlying column that serves as a support pedestal. Evidence of a recent tensile spalling failure was observed on the pedestal surface immediately beneath the contact with the overlying leaning column. The spalling of a flake-shaped piece of the pedestal, probably due to the high stress concentration exerted by the weight of the leaning column along a linear contact with the pedestal, is likely causing the present movement of the leaning column. Although it is unlikely that climbers will dislodge the leaning column by their weight alone, the possibility exists that additional spalling failures may occur from the pedestal surface and further reduce the stability of the leaning column and result in its toppling. To facilitate detection of further spalling failures from the pedestal, its surface has been coated with a layer of paint. Any new failures from the pedestal could result in the leaning column toppling onto the climbing route or onto the section of the Tower trail below.

Open-File Report

Shallow-landslide hazard map of Seattle, Washington

Landslides, particularly debris flows, have long been a significant cause of damage and destruction to people and property in the Puget Sound region. Following the years of 1996 and 1997, the Federal Emergency Management Agency (FEMA) designated Seattle as a 'Project Impact' city with the goal of encouraging the city to become more disaster resistant to the effects of landslides and other natural hazards. A major recommendation of the Project Impact council was that the city and the U.S. Geological Survey (USGS) collaborate to produce a landslide hazard map of the city. An exceptional data set archived by the city, containing more than 100 years of landslide data from severe storm events, allowed comparison of actual landslide locations with those predicted by slope-stability modeling. We used an infinite-slope analysis, which models slope segments as rigid friction blocks, to estimate the susceptibility of slopes to shallow landslides which often mobilize into debris flows, water-laden slurries that can form from shallow failures of soil and weathered bedrock, and can travel at high velocities down steep slopes. Data used for analysis consisted of a digital slope map derived from recent Light Detection and Ranging (LIDAR) imagery of Seattle, recent digital geologic mapping, and shear-strength test data for the geologic units in the surrounding area. The combination of these data layers within a Geographic Information System (GIS) platform allowed the preparation of a shallow landslide hazard map for the entire city of Seattle.

Open-File Report