Geology topics

David R. Carlson

Publications and source records attributed to David R. Carlson.

5 recordsLinked to original sources

USGS2010

Application of the surface azimuthal electrical resistivity survey method to determine patterns of regional joint orientation in glacial tills

Joints within unconsolidated material such as glacial till can be primary avenues for the flow of electrical charge, water, and contaminants. To facilitate the siting and design of remediation programs, a need exists to map anisotropic distribution of such pathways within glacial tills by determining the azimuth of the dominant joint set. The azimuthal survey method uses standard resistivity equipment with a Wenner array rotated about a fixed center point at selected degree intervals that yields an apparent resistivity ellipse. From this ellipse, joint set orientation can be determined. Azimuthal surveys were conducted at 21 sites in a 500-km2 (193 mi2) area around Milwaukee, Wisconsin, and more specifically, at sites having more than 30 m (98 ft) of glacial till (to minimize the influence of underlying bedrock joints). The 26 azimuthal surveys revealed a systematic pattern to the trend of the dominant joint set within the tills, which is approximately parallel to ice flow direction during till deposition. The average orientation of the joint set parallel with the ice flow direction is N77??E and N37??E for the Oak Creek and Ozaukee tills, respectively. The mean difference between average direct observation of joint set orientations and average azimuthal resistivity results is 8??, which is one fifth of the difference of ice flow direction between the Ozaukee and Oak Creek tills. The results of this study suggest that the surface azimuthal electrical resistivity survey method used for local in situ studies can be a useful noninvasive method for delineating joint sets within shallow geologic material for regional studies. Copyright ?? 2010 The American Association of Petroleum Geologists/Division of Environmental Geosciences. All rights reserved.

Environmental Geosciences↗

USGS2010

Use of the azimuthal resistivity technique for determination of regional azimuth of transmissivity

Many bedrock units contain joint sets that commonly act as preferred paths for the movement of water, electrical charge, and possible contaminants associated with production or transit of crude oil or refined products. To facilitate the development of remediation programs, a need exists to reliably determine regional-scale properties of these joint sets: azimuth of transmissivity ellipse, dominant set, and trend(s). The surface azimuthal electrical resistivity survey method used for local in situ studies can be a noninvasive, reliable, efficient, and relatively cost-effective method for regional studies. The azimuthal resistivity survey method combines the use of standard resistivity equipment with a Wenner array rotated about a fixed center point, at selected degree intervals, which yields an apparent resistivity ellipse from which joint-set orientation can be determined. Regional application of the azimuthal survey method was tested at 17 sites in an approximately 500 km2 (193 mi2) area around Milwaukee, Wisconsin, with less than 15m (50 ft) overburden above the dolomite. Results of 26 azimuthal surveys were compared and determined to be consistent with the results of two other methods: direct observation of joint-set orientation and transmissivity ellipses from multiple-well-aquifer tests. The average of joint-set trend determined by azimuthal surveys is within 2.5?? of the average of joint-set trend determined by direct observation of major joint sets at 24 sites. The average of maximum of transmissivity trend determined by azimuthal surveys is within 5.7?? of the average of maximum of transmissivity trend determined for 14 multiple-well-aquifer tests. Copyright ?? 2010 The American Association of Petroleum Geologists/Division of Environmental Geosciences. All rights reserved.

Environmental Geosciences↗

USGS2007

Field Demonstrations of Five Geophysical Methods that Could Be Used to Characterize Deposits of Alluvial Aggregate

Personnel from the U.S. Geological Survey and Martin Marietta Aggregates, Inc., conducted field demonstrations of five different geophysical methods to show how these methods could be used to characterize deposits of alluvial aggregate. The methods were time-domain electromagnetic sounding, electrical resistivity profiling, S-wave reflection profiling, S-wave refraction profiling, and P-wave refraction profiling. All demonstrations were conducted at one site within a river valley in central Indiana, where the stratigraphy consisted of 1 to 2 meters of clay-rich soil, 20 to 35 meters of alluvial sand and gravel, 1 to 6 meters of clay, and multiple layers of limestone and dolomite bedrock. All geophysical methods, except time-domain electromagnetic sounding, provided information about the alluvial aggregate that was consistent with the known geology. Although time-domain electromagnetic sounding did not work well at this site, it has worked well at other sites with different geology. All of these geophysical methods complement traditional methods of geologic characterization such as drilling.

Scientific Investigations Report↗

USGS2003

Incorporating uncertainty into high-resolution groundwater supply models

Groundwater modeling is a useful tool for evaluating whether an acquifer system is capable of supporting groundwater withdrawals over long periods of time and what effect, if any, such activity will have on the regional flow dynamics as well as on specific public water, agricultural and industrial supplies. An overview is given of an ongoing groundwater modeling study of the Chicot Aquifer in southwestern Louisiana where a low-resolution groundwater model is being used to study the regional flow in the Chicot acquifer and to provide boundary conditions for higher-resolution inset models created using telescopic mesh refinement (TMR).

Conference Paper↗

USGS1994

Breeding patterns and reproductive success of California sea otters

Following commercial exploitation in the eighteenth and nineteenth centuries, sea otter ( Enhydra lutris ) populations in Alaska, British Columbia, and Washington recovered at 17-20% a year, yet the California population increased at only 5% a year. This slow rate of increase is perplexing, given that unoccupied and apparently favorable habitats occur throughout the sea otter's California range, and higher growth rates occurred among northern sea otter populations. Better knowledge of the demography of the California population is important in understanding these disparate population growth rates. We studied the reproductive biology and behavior of 53 tagged female sea otters from 1985 to 1991 in Monterey Bay, California. During the study, 136 pups were born to these females. Observations of each female enabled us to determine exact or estimated pup birth dates, which we used to calculate lengths of gestation, pup dependency, and reproductive cycle. Seasonal trends in pupping, in the proportion of adult females with pups, and in pup separations from their mothers were relatively uniform throughout the year. The average interval between separation from pup and subsequent birth was 198 days, the interbirth interval was 407 days, and estimated birth rate was 0.90/year for all adult females. For females that pupped annually (did not lose undetected newborns), the average interbirth interval was 342 days, given an estimated birth rate of 1.07/year. Length of the reproductive cycle increased with increasing length of prior pup dependency. However, the interval between separation from pup and subsequent birth was delayed among females that prematurely lost their pups. The average length of dependency for pups that survived to weaning was 166 days, but ranged from 120 to 280 days. The maximum preweaning survival rate was 0.60-0.65, less than values measured or inferred for some Alaskan populations. Most pups that did not survive to weaning were lost within a month of birth. The probability of successfully weaning pups and the length of dependency increased ( P = 0.077) with mothers' ages, thus indicating that reproductive success may increase among females with greater mothering experience. The high preweaning pup mortality we observed probably accounts for much of the relatively slow growth rate of the California sea otter population.

California↗