Search USGS⌕ Search

Geology topics

David M. Rubin

Publications and source records attributed to David M. Rubin.

At least 55 records · Page 3Linked to original sources
USGS2007

Bed forms created by simulated waves and currents in a large flume

The morphology and evolution of bed forms created by combinations of waves and currents were investigated using an oscillating plate in a 4-m-wide flume. Current speed ranged from 0 to 30 cm/s, maximum oscillatory velocity ranged from 20 to 48 cm/s, oscillation period was 8 s (except for one run with 12 s period), and the median grain size was 0.27 mm. The angle between oscillations and current was 90°, 60°, or 45°. At the end of each run the sand bed was photographed and ripple dimensions were measured. Ripple wavelength was also determined from sonar images collected throughout the runs. Increasing the ratio of current to wave (i.e., oscillatory) velocity decreased ripple height and wavelength, in part because of the increased fluid excursion during the wave period. Increasing the ratio of current to waves, or decreasing the angle between current and waves, increased the three-dimensionality of bed forms. During the runs, ripple wavelength increased by a factor of about 2. The average number of wave periods for evolution of ripple wavelength to 90% of its final value was 184 for two-dimensional ripples starting from a flat bed. Bed form orientations at the end of each run were compared to four potential controlling factors: the directions of waves, current, maximum instantaneous bed shear stress, and maximum gross bed form normal transport (MGBNT). The directions of waves and of MGBNT were equally good predictors of bed form orientations, and were significantly better than the other two factors.

Journal of Geophysical Research C: Oceans↗
USGS2007

Underwater microscope for measuring spatial and temporal changes in bed-sediment grain size

For more than a century, studies of sedimentology and sediment transport have measured bed-sediment grain size by collecting samples and transporting them back to the laboratory for grain-size analysis. This process is slow and expensive. Moreover, most sampling systems are not selective enough to sample only the surficial grains that interact with the flow; samples typically include sediment from at least a few centimeters beneath the bed surface. New hardware and software are available for in situ measurement of grain size. The new technology permits rapid measurement of surficial bed sediment. Here we describe several systems we have deployed by boat, by hand, and by tripod in rivers, oceans, and on beaches.

Sedimentary Geology↗
USGS2007

Research Furthers Conservation of Grand Canyon Sandbars

Grand Canyon National Park lies approximately 25 km (15 mi) down-river from Glen Canyon Dam, which was built on the Colorado River just south of the Arizona-Utah border in Glen Canyon National Recreation Area. Before the dam began to regulate the Colorado River in 1963, the river carried such large quantities of red sediment, for which the Southwest is famous, that the Spanish named the river the Rio Colorado, or 'red river'. Today, the Colorado River usually runs clear below Glen Canyon Dam because the dam nearly eliminates the main-channel sand supply. The daily and seasonal flows of the river were also altered by the dam. These changes have disrupted the sedimentary processes that create and maintain Grand Canyon sandbars. Throughout Grand Canyon, sandbars create habitat for native plants and animals, supply camping beaches for river runners and hikers, and provide sediment needed to protect archaeological resources from weathering and erosion. Maintenance of sandbars in the Colorado River ecosystem, the river corridor that stretches from the dam to the western boundary of Grand Canyon National Park, is a goal of the Glen Canyon Dam Adaptive Management Program. The program is a federally authorized initiative to ensure that the mandates of the Grand Canyon Protection Act of 1992 are met through advances in information and resource management. The U.S. Geological Survey's Grand Canyon Monitoring and Research Center has responsibility for scientific monitoring and research efforts for the program. Extensive research and monitoring during the past decade have resulted in the identification of possible alternatives for operating Glen Canyon Dam that hold new potential for the conservation of sand resources.

Fact Sheet↗
USGS2007

The role of aeolian sediment in the preservation of archaeological sites in the Colorado River corridor, Grand Canyon, Arizona: Final report on research activities, 2003-2006

This report summarizes a three-year study of aeolian sedimentary processes in the Colorado River corridor, Grand Canyon, Arizona, and discusses the relevance of those processes to the preservation of archaeological sites. Findings are based upon detailed sedimentary and geomorphic investigations conducted in three areas of the river corridor, continuous measurements of wind, precipitation, and aeolian sediment transport at six locations for up to 26 months, short-term field study at 35 other sites, examination of historical aerial photographs, and review of data collected and analyzed by previous studies. Detailed results of this study, which involved collaboration with scientists at the Grand Canyon Monitoring and Research Center, National Park Service, Northern Arizona University, the Hopi Tribe, and GeoArch, Inc., have been published previously in topical USGS Open-File Reports (Draut and Rubin, 2005, 2006), a USGS Scientific Investigations Report (Draut and others, 2005), and will be discussed in two forthcoming journal articles. This report serves as an overview of the results and contains new conclusions regarding aeolian sedimentary processes in the Colorado River Ecosystem and their relevance to many archaeological sites.

Arizona↗
USGS2007

Seabed ripple morphology and surficial sediment size at the SAX04 experiments near Fort Walton Beach, Florida, fall 2004

Data presented in this report originates from measurements obtained off the Florida coast (fig. 1) as part of the Sediment Acoustics Experiment (SAX04) and Ripples Department Research Initiative (DRI) (Office of Naval Research (ONR), Critical Benthic Environmental Processes and Modeling, Long Range BAA 04-001, Sept. 10, 2003). The aim of this document is to present methods employed to extract data and the resulting measured ripple characteristics (ripple height, wavelength, and orientation) and seabed grain sizes. Application and analysis of the data with respect to hydro- and morphodynamics will be addressed in subsequent reports. Sediment transport in the coastal region is a complex process involving interactions between flow dynamics, sediments, and bedforms. Sediment type and bed geometry directly influence entrainment of sediments into suspension, and at sites where ripples occur (sand formations on the order of several cm high and less than two meter long wavelengths), the understanding of ripple dynamics is an essential component in improving sediment transport models. To gain a better understanding and ability to predict sediment transport, a field study was undertaken to investigate morphology, orientation, and dynamics of ripples on the seafloor. The data obtained from the field campaign also supports an on-going effort to study the effects of ripples on low grazing acoustic penetration into sandy marine sediments for the detection of objects, such as mines (Jackson and others, 2002).

Florida↗
USGS2007

Streamflow and Sediment Data Collected to Determine the Effects of Low Summer Steady Flows and Habitat Maintenance Flows in 2000 on the Colorado River between Lees Ferry and Bright Angel Creek, Arizona

The low summer steady flows (LSSF) experiment of 2000 further demonstrated that spike flows released from Glen Canyon Dam redistribute sand from the channel bed and lower elevation parts of eddy sandbars to channel-margin deposits and the higher elevation parts of eddy sandbars. Unfortunately, summer 2000 was a period of unusually low tributary influx of sediment and there was little fine sediment (i.e., sand and finer material) available for redistribution. Nevertheless, the low steady flows, which held releases from the dam steady at 230 m3/s (8,100 ft3/s), during the summer of 2000 effectively retained on the channel bed the little sediment that was supplied by tributaries, and a subsequent 4-day, 870 m3/s (30,700 ft3/s) spike flow caused modest increases in the area of the mid-elevation zone of eddy sandbars.

Open-File Report↗
USGS2006

Why deposits of longitudinal dunes are rarely recognized in the geologic record

Dunes that are morphologically of linear type, many of which are probably of longitudinal type in a morphodynamic sense, are common in modern deserts, but their deposits are rarely identified in aeolian sandstones. One reason for non-recognition of such dunes is that they can migrate laterally when they are not exactly parallel to the long-term sand-transport direction, thereby depositing cross-strata that have unimodal cross-bed dip directions and consequently resemble deposits of transverse dunes. Dune-parallel components of sand transport can be recognized in ancient aeolian sands by examining compound cross-bedding formed by small dunes that migrated across the lee slopes of large dunes and documenting that the small dunes migrated with a component in a preferred along-crest direction over the large dunes.

Sedimentology↗
USGS2006

Flume experiments on the alignment of transverse, oblique, and longitudinal dunes in directionally varying flows

For more than a century geologists have wondered why some bedforms are orientated roughly transverse to flow, whereas others are parallel or oblique to flow. This problem of bedform alignment was studied experimentally using subaqueous dunes on a 3–6-m-diameter sand-covered turntable on the floor of a 4-m-wide flume. In each experiment, two flow directions (relative to the bed) were produced by alternating the turntable between two orientations. The turntable was held in each orientation for a short time relative to the reconstitution time of the bedforms; the resulting bedforms were in equilibrium with the time-averaged conditions of the bimodal flows. Dune alignment was studied for five divergence angles (the angle between the two flow directions): 45°, 67–5°, 90°, 112–5° and 135°. The flow depth during all experiments was approximately 30 cm; mean velocity was approximately 50 cm s -1 and mean grain diameter was 0–6 mm. Each experiment continued for 30–75 min, during which time the flume flow was steady and the turntable position changed every 2 min. At the end of each experiment, water was slowly drained from the flume and dune alignment was measured. Transverse dunes (defined relative to the resultant transport direction) were created when the divergence angle was 45° and 67–5°, and longitudinal dunes were created when the divergence angle was 135°. At intermediate divergence angles, dunes with both orientations were produced, but transverse dunes were dominant at 90°, and longitudinal dunes were dominant at 112–5°. One experiment was conducted with a divergence angle of 135° and with unequal amounts of transport in the two flow directions. This was achieved by changing the orientation of the turntable at unequal time intervals, thereby causing the amount of transport to be unequal in the two directions. The dunes formed during this experiment were oblique to the resultant transport direction. These experimental dunes follow the same rule of alignment as wind ripples studied in previous turntable experiments. In both sets of experiments, the bedforms developed with the orientation having the maximum gross bedform-normal transport (the orientation at which the sum of the bedform-normal components of the two transport vectors reaches its maximum value). In other words, the bedforms develop with an orientation that is as transverse as possible to the two flows. In those cases where the two flows diverge by more than 90° and transport equal amounts of sand, bedforms that are as transverse as possible to the two separate flows will be parallel to the resultant of the two flow vectors. Although such bedforms have been defined by previous work as longitudinal bedforms, they are intrinsically the same kind of bedform as transverse bedforms.

Sedimentology↗
USGS2006

Measurements of wind, aeolian sand transport, and precipitation in the Colorado River corridor, Grand Canyon, Arizona: January 2005 to January 2006

This report presents measurements of aeolian sediment-transport rates, wind speed and direction, and precipitation records from six locations that contain aeolian deposits in the Colorado River corridor through Grand Canyon, Grand Canyon National Park, Arizona. Aeolian deposits, many of which contain and preserve archaeological material, are an important part of the Grand Canyon ecosystem. This report contains data collected between January 2005 and January 2006, and is the second in a series; the first contained data that were collected between November 2003 and December 2004 (Draut and Rubin, 2005; http://pubs.usgs.gov/of/2005/1309/ ). Analysis of data collected in 2005 shows great spatial and seasonal variation in wind and precipitation patterns. Total annual rainfall can vary by more than a factor of two over distances ~ 10 km. Western Grand Canyon received substantially more precipitation than the eastern canyon during the abnormally wet winter of 2005. Great spatial variability in precipitation indicates that future sedimentary and geomorphic studies would benefit substantially from continued or expanded data collection at multiple locations along the river corridor, because rainfall records collected by NPS at Phantom Ranch (near river-mile 88) cannot be assumed to apply to other areas of the canyon. Wind velocities and sand transport in 2005 were greatest during May and June, with maximum winds locally as high as ~25 m s -1 , and transport rates locally >100 g cm -1 d -1 . This represents a later peak in seasonal aeolian sand transport compared to the previous year, in which transport rates were greatest in April and May 2004. Dominant wind direction varies with location, but during the spring windy season the greatest transport potential was directed upstream in Marble Canyon (eastern Grand Canyon). At all locations, rates of sand transport during the spring windy season were 5–15 times higher than at other times of year. This information has been used to evaluate the potential for aeolian reworking of new fluvial sand deposits, and restoration of higher-elevation aeolian deposits, following the 60-hour controlled flood release from Glen Canyon Dam in November 2004. Substantial deposition of new sand occurred at all study sites during this high-flow experiment, but most of the new sediment was eroded by high flow fluctuations between January and March 2005. Comparison of aeolian sand transport in the spring windy seasons of the preand post-flood years indicates that, where some of the flood-deposited sand remained by spring, aeolian sand transport was significantly higher than during the pre-flood spring. Gully incision in an aeolian dune field was observed to be partially ameliorated by deposition of wind-blown sand derived from a nearby 2004 flood deposit. These results imply that sediment-rich controlled floods can renew sand deposition in aeolian dune fields above the flood-stage elevation. The potential for restoration of archaeological sites in aeolian deposits can be maximized by using dam operations that maximize the open sand area on fluvial sandbars during spring, when aeolian sediment transport is greatest.

Arizona↗
USGS2006

Underwater Microscope for Measuring Spatial and Temporal Changes in Bed-Sediment Grain Size

For more than a century, studies of sedimentology and sediment transport have measured bed-sediment grain size by collecting samples and transporting them back to the lab for grain-size analysis. This process is slow and expensive. Moreover, most sampling systems are not selective enough to sample only the surficial grains that interact with the flow; samples typically include sediment from at least a few centimeters beneath the bed surface. New hardware and software are available for in-situ measurement of grain size. The new technology permits rapid measurement of surficial bed sediment. Here we describe several systems we have deployed by boat, by hand, and by tripod in rivers, oceans, and on beaches.

Open-File Report↗
USGS2005

Sedimentology and stratigraphy of the Palisades, Lower Comanche, and Arroyo Grande areas of the Colorado River Corridor, Grand Canyon, Arizona

This report analyzes various depositional environments in three archaeologically significant areas of the Colorado River corridor in Grand Canyon. Archaeological features are built on and buried by fluvial, aeolian, and locally derived sediment, representing a complex interaction between geologic and cultural history. These analyses provide a basis for determining the potential influence of Glen Canyon Dam operations on selected archaeological sites and thus for guiding dam operations in order to facilitate preservation of cultural resources. This report presents initial results of a joint effort between geologists and archaeologists to evaluate the significance of various depositional processes and environments in the prehistoric formation and modern preservation of archaeological sites along the Colorado River corridor in Grand Canyon National Park. Stratigraphic investigations of the Palisades, Lower Comanche, and Arroyo Grande areas of Grand Canyon yield detailed information regarding the sedimentary history at these locations. Reconstruction of past depositional settings is critical to a thorough understanding of the geomorphic and stratigraphic evolution of these three archaeologically significant areas. This examination of past sedimentary environments allows the relative significance of fluvial, aeolian, debris-fan, and slope-wash sedimentary deposits to be identified at each site. In general the proportion of fluvial sediment (number and thickness of flood deposits) is shown to decrease away from the river, and locally derived sediment becomes more significant. Flood sequences often occur as 'couplets' that contain a fluvial deposit overlain by an interflood unit that reflects reworking of fluvial sediment at the land surface by wind and local runoff. Archaeological features are built on and buried by sediment of various depositional environments, implying a complex interaction between geologic and cultural history. Such field analysis, which combines geological and archaeological information and techniques, can provide a basis for future determination of the effects of Glen Canyon Dam operations on selected areas of the river corridor. This knowledge is essential to the development of preservation strategies for cultural resources in Grand Canyon.

Scientific Investigations Report↗
USGS2004

Estimating accumulation rates and physical properties of sediment behind a dam: Englebright Lake, Yuba River, northern California

Studies of reservoir sedimentation are vital to understanding scientific and management issues related to watershed sediment budgets, depositional processes, reservoir operations, and dam decommissioning. Here we quantify the mass, organic content, and grain-size distribution of a reservoir deposit in northern California by two methods of extrapolating measurements of sediment physical properties from cores to the entire volume of impounded material. Englebright Dam, completed in 1940, is located on the Yuba River in the Sierra Nevada foothills. A research program is underway to assess the feasibility of introducing wild anadromous fish species to the river upstream of the dam. Possible management scenarios include removing or lowering the dam, which could cause downstream transport of stored sediment. In 2001 the volume of sediments deposited behind Englebright Dam occupied 25.5% of the original reservoir capacity. The physical properties of this deposit were calculated using data from a coring campaign that sampled the entire reservoir sediment thickness (6–32 m) at six locations in the downstream ∼3/4 of the reservoir. As a result, the sediment in the downstream part of the reservoir is well characterized, but in the coarse, upstream part of the reservoir, only surficial sediments were sampled, so calculations there are more uncertain. Extrapolation from one-dimensional vertical sections of sediment sampled in cores to entire three-dimensional volumes of the reservoir deposit is accomplished via two methods, using assumptions of variable and constant layer thickness. Overall, the two extrapolation methods yield nearly identical estimates of the mass of the reservoir deposit of ∼26 × 10 6 metric tons (t) of material, of which 64.7–68.5% is sand and gravel. Over the 61 year reservoir history this corresponds to a maximum basin-wide sediment yield of ∼340 t/km 2 /yr, assuming no contribution from upstream parts of the watershed impounded by other dams. The uncertainties and limitations of the estimates of overall sediment quantities are discussed. Implications for watershed management and future reservoir sedimentation studies are also presented.

California↗
USGS2003

Tsunami

No abstract available.

Earthquake Spectra↗
USGS2003

Bed-sediment grain-size and morphologic data from Suisun, Grizzly, and Honker Bays, CA, 1998-2002

The USGS Place Based Studies Program for San Francisco Bay investigates this sensitive estuarine system to aid in resource management. As part of the inter-disciplinary research program, the USGS collected side-scan sonar data and bed-sediment samples from north San Francisco Bay to characterize bed-sediment texture and investigate temporal trends in sedimentation. The study area is located in central California and consists of Suisun Bay, and Grizzly and Honker Bays, sub-embayments of Suisun Bay. During the study (1998-2002), the USGS collected three side-scan sonar data sets and approximately 300 sediment samples. The side-scan data revealed predominantly fine-grained material on the bayfloor. We also mapped five different bottom types from the data set, categorized as featureless, furrows, sand waves, machine-made, and miscellaneous. We performed detailed grain-size and statistical analyses on the sediment samples. Overall, we found that grain size ranged from clay to fine sand, with the coarsest material in the channels and finer material located in the shallow bays. Grain-size analyses revealed high spatial variability in size distributions in the channel areas. In contrast, the shallow regions exhibited low spatial variability and consistent sediment size over time.

California↗