Geology topics

Christopher B. DuRoss

Publications and source records attributed to Christopher B. DuRoss.

At least 55 records · Page 3Linked to original sources

USGS2019

Stratigraphic and structural relations in trench exposures and geomorphology at the Big Burn, Lily Lake, and Lester Ranch sites, Bear River Fault Zone, Utah and Wyoming

This report provides trench photomosaics, logs and related site information, age data, and earthquake event evidence from three paleoseismic trench sites on the Bear River Fault Zone. Our motivation for studying the Bear River Fault Zone—a nascent normal fault in the Rocky Mountains east of the Basin and Range physiographic province—is twofold: (1) the intriguing conclusion from previous work that the neotectonic history of the fault may have begun in the middle to late Holocene and consists of only two surface-rupturing earthquakes and (2) the question of whether large scarps (>10 meters in height) observed along the fault represent net tectonic displacement, which, given a two-event history, would put the displacements among the largest in the Basin and Range region. In presenting our trench and initial geomorphic interpretations, this report lays the groundwork for further exploration of these issues.

Utah, Wyoming↗

USGS2019

Four major Holocene earthquakes on the Reelfoot fault recorded by sackungen in the New Madrid seismic zone, USA

Three sequences of well-documented, major ~M7+ earthquakes (1811-1812 CE, ~1450 CE, and ~900 CE) in the New Madrid seismic zone, USA, contribute significantly to seismic hazard in the region. However, it is unknown whether this <550 yr recurrence interval has been constant throughout the Holocene given limited geomorphic evidence of prior earthquakes. We extend the record of paleoearthquakes along the Reelfoot fault via investigation of ridge-top gravitational failure features, interpreted as sackungen. The sackungen occur in bluffs along the eastern margin of the Mississippi River floodplain and are concentrated near (<15 km) the southwest-dipping Reelfoot reverse fault. A paleoseismic trench excavated across sackungen at the Paw Paw site exposed four packages of colluvial sediment that postdate 30-11 ka Peoria loess. We interpret the colluvial packages to have been deposited following episodic failure of the sackungen as a result of strong ground motions from the following sequence of earthquakes: event 4, 1640 ± 1730 BCE; event 3, 340 ± 670 CE; event 2, 1430 ± 380 CE; and event 1, 1810 ± 50 CE (2-sigma). Event timing corresponds to previously documented earthquakes and represents the longest archive of paleoearthquakes on the Reelfoot fault. If the trenched sackungen record all major Reelfoot fault earthquakes, our observations in combination with prior investigations indicate a period of quiescence from at least 11 – 4.7 ka, followed by four major seismic events culminating in the 1811-1812 CE sequence. This clustered earthquake recurrence helps place bounds on seismic-hazard and geodynamic models in the New Madrid seismic zone.

Arkansas, Missouri↗

USGS2019

Preliminary report on engineering and geological effects of the July 2019 Ridgecrest earthquake sequence

The Ridgecrest Earthquake sequence included a foreshock event on July 4 2019 (M6.4) and a M7.1 mainshock event on July 5 2019. These events occurred in the Eastern California Shear Zone, near Indian Wells Valley, south of China Lake and west of Searles Valley. GEER has partnered with several organizations to collect perishable data and document the important impacts of these events, including the US Geological Survey, the California Geological Survey, the US Navy, the Southern California Earthquake Center, and local utilities. Critical geotechnical features of this event are extensive left-lateral (M6.4 event) and right-lateral (M7.1 event) surface ruptures over fault segments of variable complexity and width as well as across extensional and compressive step-over zones. We also document lifeline performance at fault crossings (gas, water, electrical), mainshock slip and afterslip, liquefaction and lateral spreading features, and liquefaction effects on structures. These effects are documented using field (ground) mapping and aerial imagery that will support subsequent development of high-resolution digital elevation models. Over 750 ground motions were recorded from the foreshock and mainshock alone, with many additional aftershock records. The data demonstrate significant impacts of site response and rupture directivity on ground motion attributes.

Report↗

USGS2019

The Teton fault

No abstract available.

Wyoming↗

USGS2018

Paleoseismic results from the Alpine site, Wasatch fault zone: Timing and displacement data for six holocene earthquakes at the Salt Lake City–Provo segment boundary

To improve the characterization of Holocene earthquakes on the Wasatch fault zone (WFZ), we conducted light detection and ranging (lidar)‐based neotectonic mapping and excavated a paleoseismic trench across an 8‐m‐high fault scarp near Alpine, Utah, located < 1    km "> < 1 km <1 km south of the boundary between the Salt Lake City and Provo segments (SLCS and PS). We document evidence for six paleoearthquakes (AL6–AL1) from scarp‐derived colluvial wedges and crosscutting relations. A ground‐penetrating radar survey across the scarp resolved fault‐zone width, but not paleoearthquake stratigraphy. Bayesian (OxCal) modeling of 13 radiocarbon and 13 optically stimulated luminescence ages indicates that six earthquakes occurred ∼ 6.2 – 0.4    ka "> ∼ 6.2 – 0.4 ka ∼6.2–0.4 ka . Interseismic recurrence ranges from 0.2 to 1.8 ky (mean 1.2 ky). We estimate 6.5 ± 0.7    m "> 6.5 ± 0.7 m 6.5±0.7 m of cumulative vertical tectonic displacement across the ≥ 14 ‐ m ‐ wide "> ≥ 14 ‐ m ‐ wide ≥14‐m‐wide fault zone used near‐field observations of scarp‐derived colluvial‐wedge thicknesses, antithetic faulting, and graben backtilting. This is similar to our independent estimate of 6.5 ± 0.5    m "> 6.5 ± 0.5 m 6.5±0.5 m using far‐field observations of the offset ground surface and correlation of alluvial‐fan stratigraphy across the WFZ. These results suggest that colluvial‐wedge thickness at the Alpine site approximates one‐half the original west‐facing fault scarp height. Per‐event vertical displacements range from 0.8 to 1.2 m (mean 1.1 m), which we use to estimate surface rupture lengths that may exceed 50 km from earthquakes as large as moment magnitude ( M w "> M w Mw ) ∼ 7.0 "> ∼ 7.0 ∼7.0 . The late Holocene average vertical slip rate is 0.9    mm / yr "> 0.9 mm / yr 0.9 mm/yr ( 0.7 – 1.2    mm / yr "> 0.7 – 1.2 mm / yr 0.7–1.2 mm/yr range). Earthquake frequency has increased in the past ∼ 1    ky "> ∼ 1 ky ∼1 ky , whereas displacement per event has been similar for the past ∼ 6    ky "> ∼ 6 ky ∼6 ky , suggesting that strain accumulation is not the sole factor that controls the frequency and size of earthquakes at the SLCS–PS segment boundary. These findings can be used for a more nuanced characterization of earthquakes at the SLCS–PS boundary and improve earthquake hazard assessments along the Wasatch Front.

Utah↗

USGS2018

Combining conflicting Bayesian models to develop paleoseismic records—An example from the Wasatch Fault Zone, Utah

Bayesian statistical analyses of paleoseismic data result in the probabilistic determination of earthquake times using geochronological data evaluated in the context of a stratigraphic model. However, a fundamental problem in paleoseismology is how to use the Bayesian approach to model sparse and/or conflicting geochronological datasets, such as those derived from sites exhibiting episodic sedimentary and pedogenic processes in moderate‐ to high‐energy environments (e.g., a normal‐faulted alluvial fan). Using paleoseismic data for the Corner Canyon site on the Salt Lake City segment of the Wasatch fault zone (Utah), we develop an approach by which multiple Bayesian models are combined to generate an earthquake history at a site. This approach accommodates mutually exclusive interpretations of the geochronological data and thereby limits the influence of sparse data, stratigraphically inconsistent ages, or a single, subjective model interpretation. For the Corner Canyon site, we integrate four OxCal Bayesian models to generate a chronology of six events between ∼ 4.8 "> ∼ 4.8 and ∼ 0.5    ka "> ∼ 0.5 ka ⁠ . Late Holocene (post‐5 ka) mean recurrence and vertical slip‐rate estimates are ∼ 0.9    ky "> ∼ 0.9 ky (0.7–1.0 ky; 95% confidence) and 1.1    mm / yr "> 1.1 mm / yr ( ⁠ 0.8 – 1.7    mm / yr "> 0.8 – 1.7 mm / yr range), respectively. Although our method increases the uncertainty in the timing of individual earthquakes, it more objectively accounts for potential geochronological errors and different interpretations of stratigraphic age control. By relaxing the need to select a single age model, our approach yields more accurate earthquake‐timing results that will better facilitate evaluations of along‐fault event correlation and earthquake rupture length.

Utah↗

USGS2017

High-resolution seismic profiling reveals faulting associated with the 1934 Ms 6.6 Hansel Valley earthquake (Utah, USA)

The 1934 Ms 6.6 Hansel Valley, Utah, earthquake produced an 8-km-long by 3-km-wide zone of north-south−trending surface deformation in an extensional basin within the easternmost Basin and Range Province. Less than 0.5 m of purely vertical displacement was measured at the surface, although seismologic data suggest mostly strike-slip faulting at depth. Characterization of the origin and kinematics of faulting in the Hansel Valley earthquake is important to understand how complex fault ruptures accommodate regions of continental extension and transtension. Here, we address three questions: (1) How does the 1934 surface rupture compare with faults in the subsurface? (2) Are the 1934 fault scarps tectonic or secondary features? (3) Did the 1934 earthquake have components of both strike-slip and dip-slip motion? To address these questions, we acquired a 6.6-km-long, high-resolution seismic profile across Hansel Valley, including the 1934 ruptures. We observed numerous east- and west-dipping normal faults that dip 40°−70° and offset late Quaternary strata from within a few tens of meters of the surface down to a depth of ∼1 km. Spatial correspondence between the 1934 surface ruptures and subsurface faults suggests that ruptures associated with the earthquake are of tectonic origin. Our data clearly show complex basin faulting that is most consistent with transtensional tectonics. Although the kinematics of the 1934 earthquake remain underconstrained, we interpret the disagreement between surface (normal) and subsurface (strike-slip) kinematics as due to slip partitioning during fault propagation and to the effect of preexisting structural complexities. We infer that the 1934 earthquake occurred along an ∼3-km wide, off-fault damage zone characterized by distributed deformation along small-displacement faults that may be alternatively activated during different earthquake episodes.

Utah↗

USGS2017

Refining fault slip rates using multiple displaced terrace risers-An example from the Honey Lake fault, NE California, USA

Faulted terrace risers are semi-planar features commonly used to constrain Quaternary slip rates along strike-slip faults . These landforms are difficult to date directly and therefore their ages are commonly bracketed by age estimates of the adjacent upper and lower terrace surfaces. However, substantial differences in the ages of the upper and lower terrace surfaces (a factor of 2.4 difference observed globally) produce large uncertainties in the slip-rate estimate. In this investigation, we explore how the full range of displacements and bounding ages from multiple faulted terrace risers can be combined to yield a more accurate fault slip rate. We use 0.25-m cell size digital terrain models derived from airborne lidar data to analyze three sites where terrace risers are offset right-laterally by the Honey Lake fault in NE California, USA. We use ages for locally extensive subhorizontal surfaces to bracket the time of riser formation: an upper surface is the bed of abandoned Lake Lahontan having an age of 15.8 ± 0.6 ka and a lower surface is a fluvial terrace abandoned at 4.7 ± 0.1 ka. We estimate lateral offsets of the risers ranging between 6.6 and 28.3 m (median values), a greater than fourfold difference in values. The amount of offset corresponds to the riser's position relative to modern stream meanders: the smallest offset is in a meander cutbank position, whereas the larger offsets are in straight channel or meander point-bar positions. Taken in isolation, the individual terrace-riser offsets yield slip rates ranging from 0.3 to 7.1 mm/a. However, when the offset values are collectively assessed in a probabilistic framework, we find that a uniform (linear) slip rate of 1.6 mm/a (1.4–1.9 mm/a at 95% confidence) can satisfy the data, within their respective uncertainties. This investigation demonstrates that integrating observations of multiple offset elements (crest, midpoint, and base) from numerous faulted and dated terrace risers at closely spaced sites can refine slip-rate estimates on strike-slip faults.

California↗

USGS2017

Holocene surface-faulting earthquakes at the Spring Lake and North Creek Sites on the Wasatch Fault Zone: Evidence for complex rupture of the Nephi Segment

The Nephi segment of the Wasatch fault zone (WFZ) comprises two fault strands, the northern and southern strands, which have evidence of recurrent late Holocene surface-faulting earthquakes. We excavated paleoseismic trenches across these strands to refine and expand their Holocene earthquake chronologies; improve estimates of earthquake recurrence, displacement, and fault slip rate; and assess whether the strands rupture separately or synchronously in large earthquakes. Paleoseismic data from the Spring Lake site expand the Holocene record of earthquakes on the northern strand: at least five to seven earthquakes ruptured the Spring Lake site at 0.9 ± 0.2 ka (2σ), 2.9 ± 0.7 ka, 4.0 ± 0.5 ka, 4.8 ± 0.8 ka, 5.7 ± 0.8 ka, 6.6 ± 0.7 ka, and 13.1 ± 4.0 ka, yielding a Holocene mean recurrence of ~1.2–1.5 kyr and vertical slip rate of ~0.5–0.8 mm/yr. Paleoseismic data from the North Creek site help refine the Holocene earthquake chronology for the southern strand: at least five earthquakes ruptured the North Creek site at 0.2 ± 0.1 ka (2σ), 1.2 ± 0.1 ka, 2.6 ± 0.9 ka, 4.0 ± 0.1 ka, and 4.7 ± 0.7 ka, yielding a mean recurrence of 1.1–1.3 kyr and vertical slip rate of ~1.9–2.0 mm/yr. We compare these Spring Lake and North Creek data with previous paleoseismic data for the Nephi segment and report late Holocene mean recurrence intervals of ~1.0–1.2 kyr for the northern strand and ~1.1–1.3 kyr for the southern strand. The northern and southern strands have similar late Holocene earthquake histories, which allow for models of both independent and synchronous rupture. However, considering the earthquake timing probabilities and per-event vertical displacements, we have the greatest confidence in the simultaneous rupture of the strands, including rupture of one strand with spillover rupture to the other. Ultimately, our results improve the surface-faulting earthquake history of the Nephi segment and enhance our understanding of how structural barriers influence normal-fault rupture.

Utah↗

USGS2017

The history of late holocene surface-faulting earthquakes on the central segments of the Wasatch fault zone, Utah

The Wasatch fault (WFZ)—Utah’s longest and most active normal fault—forms a prominent eastern boundary to the Basin and Range Province in northern Utah. To provide paleoseismic data for a Wasatch Front regional earthquake forecast, we synthesized paleoseismic data to define the timing and displacements of late Holocene surface-faulting earthquakes on the central five segments of the WFZ. Our analysis yields revised histories of large (M ~7) surface-faulting earthquakes on the segments, as well as estimates of earthquake recurrence and vertical slip rate. We constrain the timing of four to six earthquakes on each of the central segments, which together yields a history of at least 24 surface-faulting earthquakes since ~6 ka. Using earthquake data for each segment, inter-event recurrence intervals range from about 0.6 to 2.5 kyr, and have a mean of 1.2 kyr. Mean recurrence, based on closed seismic intervals, is ~1.1–1.3 kyr per segment, and when combined with mean vertical displacements per segment of 1.7–2.6 m, yield mean vertical slip rates of 1.3–2.0 mm/yr per segment. These data refine the late Holocene behavior of the central WFZ; however, a significant source of uncertainty is whether structural complexities that define the segments of the WFZ act as hard barriers to ruptures propagating along the fault. Thus, we evaluate fault rupture models including both single-segment and multi-segment ruptures, and define 3–17-km-wide spatial uncertainties in the segment boundaries. These alternative rupture models and segment-boundary zones honor the WFZ paleoseismic data, take into account the spatial and temporal limitations of paleoseismic data, and allow for complex ruptures such as partial-segment and spillover ruptures. Our data and analyses improve our understanding of the complexities in normal-faulting earthquake behavior and provide geological inputs for regional earthquake-probability and seismic hazard assessments.

Book chapter↗

USGS2016

Earthquake forecast for the Wasatch Front region of the Intermountain West

The Working Group on Utah Earthquake Probabilities has assessed the probability of large earthquakes in the Wasatch Front region. There is a 43 percent probability of one or more magnitude 6.75 or greater earthquakes and a 57 percent probability of one or more magnitude 6.0 or greater earthquakes in the region in the next 50 years. These results highlight the threat of large earthquakes in the region.

Utah↗

USGS2016

Fault segmentation: New concepts from the Wasatch Fault Zone, Utah, USA

The question of whether structural segment boundaries along multisegment normal faults such as the Wasatch fault zone (WFZ) act as persistent barriers to rupture is critical to seismic hazard analyses. We synthesized late Holocene paleoseismic data from 20 trench sites along the central WFZ to evaluate earthquake rupture length and fault segmentation. For the youngest (<3 ka) and best-constrained earthquakes, differences in earthquake timing across prominent primary segment boundaries, especially for the most recent earthquakes on the north-central WFZ, are consistent with segment-controlled ruptures. However, broadly constrained earthquake times, dissimilar event times along the segments, the presence of smaller-scale (subsegment) boundaries, and areas of complex faulting permit partial-segment and multisegment (e.g., spillover) ruptures that are shorter (~20–40 km) or longer (~60–100 km) than the primary segment lengths (35–59 km). We report a segmented WFZ model that includes 24 earthquakes since ~7 ka and yields mean estimates of recurrence (1.1–1.3 kyr) and vertical slip rate (1.3–2.0 mm/yr) for the segments. However, additional rupture scenarios that include segment boundary spatial uncertainties, floating earthquakes, and multisegment ruptures are necessary to fully address epistemic uncertainties in rupture length. We compare the central WFZ to paleoseismic and historical surface ruptures in the Basin and Range Province and central Italian Apennines and conclude that displacement profiles have limited value for assessing the persistence of segment boundaries but can aid in interpreting prehistoric spillover ruptures. Our comparison also suggests that the probabilities of shorter and longer ruptures on the WFZ need to be investigated.

Utah↗

USGS2016

Earthquake probabilities for the Wasatch front region in Utah, Idaho, and Wyoming

In a letter to The Salt Lake Daily Tribune in September 1883, U.S. Geological Survey (USGS) geologist G.K. Gilbert warned local residents about the implications of observable fault scarps along the western base of the Wasatch Range. The scarps were evidence that large surface-rupturing earthquakes had occurred in the past and more would likely occur in the future. The main actor in this drama is the 350-km-long Wasatch fault zone (WFZ), which extends from central Utah to southernmost Idaho. The modern Wasatch Front urban corridor, which follows the valleys on the WFZ’s hanging wall between Brigham City and Nephi, is home to nearly 80% of Utah’s population of 3 million. Adding to this circumstance of “lots of eggs in one basket,” more than 75% of Utah’s economy is concentrated along the Wasatch Front in Utah’s four largest counties, literally astride the five central and most active segments of the WFZ.

Utah, Idaho, Wyoming↗

USGS2015

High‐resolution trench photomosaics from image‐based modeling: Workflow and error analysis

Photomosaics are commonly used to construct maps of paleoseismic trench exposures, but the conventional process of manually using image‐editing software is time consuming and produces undesirable artifacts and distortions. Herein, we document and evaluate the application of image‐based modeling (IBM) for creating photomosaics and 3D models of paleoseismic trench exposures, illustrated with a case‐study trench across the Wasatch fault in Alpine, Utah. Our results include a structure‐from‐motion workflow for the semiautomated creation of seamless, high‐resolution photomosaics designed for rapid implementation in a field setting. Compared with conventional manual methods, the IBM photomosaic method provides a more accurate, continuous, and detailed record of paleoseismic trench exposures in approximately half the processing time and 15%–20% of the user input time. Our error analysis quantifies the effect of the number and spatial distribution of control points on model accuracy. For this case study, an ∼87 m 2 exposure of a benched trench photographed at viewing distances of 1.5–7 m yields a model with <2 cm root mean square error (rmse) with as few as six control points. Rmse decreases as more control points are implemented, but the gains in accuracy are minimal beyond 12 control points. Spreading control points throughout the target area helps to minimize error. We propose that 3D digital models and corresponding photomosaics should be standard practice in paleoseismic exposure archiving. The error analysis serves as a guide for future investigations that seek balance between speed and accuracy during photomosaic and 3D model construction.

Bulletin of the Seismological Society of America↗

USGS2015

Analysis and selection of magnitude relations for the Working Group on Utah Earthquake Probabilities

Prior to calculating time-independent and -dependent earthquake probabilities for faults in the Wasatch Front region, the Working Group on Utah Earthquake Probabilities (WGUEP) updated a seismic-source model for the region (Wong and others, 2014) and evaluated 19 historical regressions on earthquake magnitude (M). These regressions relate M to fault parameters for historical surface-faulting earthquakes, including linear fault length (e.g., surface-rupture length [SRL] or segment length), average displacement, maximum displacement, rupture area, seismic moment (Mo ), and slip rate. These regressions show that significant epistemic uncertainties complicate the determination of characteristic magnitude for fault sources in the Basin and Range Province (BRP). For example, we found that M estimates (as a function of SRL) span about 0.3–0.4 units (figure 1) owing to differences in the fault parameter used; age, quality, and size of historical earthquake databases; and fault type and region considered.

Conference Paper↗

USGS2014

History of late Holocene earthquakes at the Willow Creek site on the Nephi segment, Wasatch fault zone, Utah

This 43-page report presents new data from the Willow Creek site that provides well-defined and narrow bounds on the times of the three youngest earthquakes on the southern strand of the Nephi segment, Wasatch Fault zone, and refines the time of the youngest earthquake to about 200 years ago. This is the youngest surface rupture on the entire Wasatch fault zone, which occurred about a century or less before European settles arrived in Utah. Two trenches at the Willow Creek site exposed three scarp-derived colluvial wedges that are evidence of three paleoearthquakes. OxCal modeling of ages from Willow Creek indicate that paleoearthquake WC1 occurred at 0.2 ± 0.1 ka, WC2 occurred at 1.2 ± 0.1 ka, and WC3 occurred at 1.9 ± 0.6 ka. Stratigraphic constraints on the time of paleoearthquake WC4 are extremely poor, so OxCal modeling only yields a broadly constrained age of 4.7 ± 1.8 ka. Results from the Willow Creek site significantly refine the times of late Holocene earthquakes on the Southern strand of the Nephi segment, and this result, when combined with a reanalysis of the stratigraphic and chronologic information from previous investigations at North Creek and Red Canyon, yield a stronger basis of correlating individual earthquakes between all three sites.

Paleoseismology of Utah↗

USGS2014

Holocene and latest Pleistocene paleoseismology of the Salt Lake City segment of the Wasatch Fault Zone, Utah, at the Penrose Drive Trench Site

The Salt Lake City segment (SLCS) of the Wasatch fault zone (WFZ) and the West Valley fault zone (WVFZ) compromise Holocene-active normal faults that bound a large intrabasin graben in northern Salt Lake Valley and have evidence of recurrent, large-magnitude (M ~6-7) surface-faulting earthquakes. However, at the time of this investigation, questions remained regarding the timing, displacement, and recurrence of latest Pleistocene and Holocene earthquakes on the northern SLCS and WVFZ , and whether the WVFZ is seismically independent of, or moves coseismically with, the SLCS. To improve paleoseismic data for the SLCS, we conducted a fault-trench investigation at the Penrose Drive site on the northern SLCS. Two trenches, excavated across an 11-m-high scarp near the northern end of the East Bench fault, exposed colluvial-wedge evidence for fize of six (preferred) surface-faulting earthquakes postdating to Provo-phase shoreline of Lake Bonneville (~14-18 ka). Radiocarbon and luminescence ages support earthquake times at 4.0 ± 0.5 ka (2σ) (PD1), 5.9 ± 0.7 ka (PD2), 7.5 ± 0.8 ka (PD3a), 9.7 ± 1.1 ka (PD3b), 10.9 ± 0.2 ka (PD4), and 12.1 ± 1.6 ka (PD5). At least one additional earthquake occurred at 16.5 ± 1.9 ka (PD6) based on an erosional unconformity that separates deformed Lake Bonneville sily and flat-lying Provo-phase shoreline gravel. Earthquakes PD5-PD1 yield latest Pleistocene (post-Provo) and Holocene mean recurrence intervals of ~1.6 kyr and ~1.7-1.9 kyr, respectively. Using 1.0-1.4 m of per-event vertical displacement for PD5-PD3b corroborate previously identified SLCS earthquakes at 4-10 ka. PD4 and PD5 occurred within an ~8-kyr *17-9 ka) time interval on the SLCS previously interpreted as a period of seismic quiescence, and PD6 possibly corresponds with a previously identified earthquake at ~17 ka (although both events have large timing uncertainties). The Penrose data, when combined with previous paleoseismic results, improve the latest Pleistocene-Holocene earthquake chronology of the SLCS, and demonstrate that the SLCS has been a consistently active source of large-magnitude earthquakes since the latest Pleistocene. At least nine surface-faulting earthquakes (S1-S9) have occurred since the highstand of Lake Bonneville (~18 ka). Where the SLCS earthquake record is most complete (since ~14 ka), per-site estimates of mean recurrence are similar for the latest Pleistocene (post-Provo) (~1.6 kyr), Holocene (~1.6-1.9 kyr), and late Holocene (~1.2-1.4 kyr). These SLCS paleoearthquake data indicate an essentially stable rate of earthquake recurrence since the latest Pleistocene and are important for understanding the earthquake potential of the SLCS, clarifying the seismogenic relation between the SLCS and WVFZ, and forecasting the probabilities of future large-magnitude earthquake in the Wasatch Front region.

Utah↗

USGS2014

Late quaternary paleoseismology of the west valley fault zone: Insights from the Baileys Lake trench site

Explore the source record for details and available documents.

Utah Geological Survey Special Study↗