Geology topics

Brian D. Collins

Publications and source records attributed to Brian D. Collins.

69 records · Page 4Linked to original sources

USGS2011

Stability of steep slopes in cemented sands

The analysis of steep slope and cliff stability in variably cemented sands poses a significant practical challenge as routine analyses tend to underestimate the actually observed stability of existing slopes. The presented research evaluates how the degree of cementation controls the evolution of steep sand slopes and shows that the detailed slope geometry is important in determining the characteristics of the failure mode, which in turn, guide the selection of an appropriate stability analysis method. Detailed slope-profile cross sections derived from terrestrial lidar surveying of otherwise inaccessible cemented sand cliffs are used to investigate failure modes in weakly cemented [unconfined compressive strength ( UCS ) < 30   kPa "> ( UCS ) < 30 kPa (UCS)<30 kPa ] and moderately cemented ( 30 < UCS < 400   kPa ) "> ( 30 < UCS < 400 kPa ) (30<UCS<400 kPa) sands and their role in the evolution of the geometry of the slopes. The results show that high-resolution slope topography, such as can be obtained with terrestrial lidar, is essential for identifying altogether different failure modes in weakly cemented (shear-mode) and moderately cemented (tensile-mode) sand slopes. Analyses show that the standard Culmann method for steep slopes is inappropriate for modeling the stability of cemented sand slopes since it tends to overpredict expected crest retreat and underestimate failure plane angle. Instead, a simplified analysis using infinite slope assumptions, but applied to a slope with finite dimensions subject to changing geometric conditions, such as toe erosion and slope steepening, is suggested for analysis of weakly cemented sand slopes. For moderately cemented sand slopes, a limit equilibrium analysis directly comparing the cliff tensile stress and cemented sand tensile strength is shown to reasonably predict failure conditions and timing as a result of either slope steepening or tensile strength loss, presumably from wetting in most cases.

Journal of Geotechnical and Geoenvironmental Engin↗

USGS2011

High-resolution three-dimensional imaging and analysis of rock falls in Yosemite valley, California

We present quantitative analyses of recent large rock falls in Yosemite Valley, California, using integrated high-resolution imaging techniques. Rock falls commonly occur from the glacially sculpted granitic walls of Yosemite Valley, modifying this iconic landscape but also posing significant potential hazards and risks. Two large rock falls occurred from the cliff beneath Glacier Point in eastern Yosemite Valley on 7 and 8 October 2008, causing minor injuries and damaging structures in a developed area. We used a combination of gigapixel photography, airborne laser scanning (ALS) data, and ground-based terrestrial laser scanning (TLS) data to characterize the rock-fall detachment surface and adjacent cliff area, quantify the rock-fall volume, evaluate the geologic structure that contributed to failure, and assess the likely failure mode. We merged the ALS and TLS data to resolve the complex, vertical to overhanging topography of the Glacier Point area in three dimensions, and integrated these data with gigapixel photographs to fully image the cliff face in high resolution. Three-dimensional analysis of repeat TLS data reveals that the cumulative failure consisted of a near-planar rock slab with a maximum length of 69.0 m, a mean thickness of 2.1 m, a detachment surface area of 2750 m 2 , and a volume of 5663 ± 36 m 3 . Failure occurred along a surface-parallel, vertically oriented sheeting joint in a clear example of granitic exfoliation. Stress concentration at crack tips likely propagated fractures through the partially attached slab, leading to failure. Our results demonstrate the utility of high-resolution imaging techniques for quantifying far-range (>1 km) rock falls occurring from the largely inaccessible, vertical rock faces of Yosemite Valley, and for providing highly accurate and precise data needed for rock-fall hazard assessment.

Geosphere↗

USGS2011

Evaluation of landslide monitoring in the Polish Carpathians

In response to the June 15, 2010 request from the Polish Geological Institute (PGI) to the U.S. Geological Survey (USGS) for assistance and advice regarding real-time landslide monitoring, landslide specialists from the USGS Landslide Hazard Program visited PGI headquarters and field sites in September 2010. During our visit we became familiar with characteristics of landslides in the Polish Carpathians, reviewed PGI monitoring techniques, and assessed needs for monitoring at recently activated landslides. Visits to several landslides that are monitored by PGI (the Just, Hańczowa, Szymbark, Siercza and Łasńica landslides) revealed that current data collection (monthly GPS and inclinometer surveys, hourly piezometers readings) is generally sufficient for collecting basic information about landslide displacement, depth, and groundwater conditions. Large landslides are typically hydrologically complex, and we would expect such complexity in Carpathian landslides, given the alternating shale and sandstone stratigraphy and complex geologic structures of the flysch bedrock. Consequently groundwater observations could be improved by installing several piezometers that sample the basal shear zone of each landslide being monitored by PGI. These could be supplemented by additional piezometers at shallower depths to help clarify general flow directions and hydraulic gradients. Remedial works at Hańczowa make the landslide unsuitable for monitoring as part of an early warning network. Monitoring there should focus on continued performance of the remedial works. Our suggestions for new monitoring at recently activated landslides are summarized in table 1. Displacement monitoring using extensometers and (or) GPS is a high priority at Kłodne, Łaśnica, Łazki, and Siedloki. Geomorphologic mapping of active surface features (scarps, cracks, shear zones, folds, and thrusts) in sufficient detail to reveal the kinematics of each landslide would greatly help in planning subsurface exploration and monitoring. Mapping should take advantage of existing and future airborne lidar data sets of specific areas, where available. Borehole inclinometers and piezometers would complete the basic monitoring package for these landslides. The landslide at Kłodne may be well suited for more detailed monitoring for landslide process research, although research opportunities exist at the other landslides as well. The landslide near Siedloki may be a good candidate for terrestrial laser scanning (TLS). Tandem streamflow gages upstream and downstream from the Siedloki landslide, or laser distance meters to monitor advancement of the toe, may be needed to provide warning of stream blockage of Potok Milowski. A real-time warning system specifically for the Łazki landslide might be considered due to potential concerns about catastrophic movement into Międzybrodzie Reservoir. Challenges associated with the establishment of a complete real-time monitoring and early warning system are far greater than just the technical and logistical aspects of installing remote monitoring systems at a large number of landslides. Long-term maintenance of a landslide monitoring network will involve considerable effort and expense as sensors break-down from exposure to weather, landslide movement, and harsh underground environmental conditions. Once PGI’s planned pilot network of 10-20 monitored landslides is operating, a period of observation and analysis will be needed to establish appropriate alert levels and criteria for issuing alerts and warnings. Simultaneously, discussions with authorities will be needed to develop action plans for responding to landslide notifications and (or) warnings. Public resistance to landslide warnings and mandated evacuations may be high given the low historical incidence of fatalities and injuries resulting from Carpathian landslides and the small potential for warnings to reduce landslide damage to homes and land. Careful weighing of purpose, advantages, and costs of a large-scale monitoring and early warning program is needed early in the planning process and should be revisited regularly throughout pilot and final implementation. In this report, we present a generic plan for monitoring of a hypothetical Carpathian landslide that illustrates how our suggestions for each of the specific landslides could be implemented. The plan includes basic pore pressure, displacement, and weather monitoring, along with supplemental monitoring for special conditions at specific landslides. Table 2 summarizes the overall approach and basic equipment and software requirements.

Open-File Report↗

USGS2011

Rainfall infiltration-induced landslides

Unfavorable groundwater conditions are often the determining factor in triggering landslides. Whereas regional hydrogeology typically determines overall groundwater conditions, surficial rainfall infiltration into slopes also drives potential instability.

Geostrata↗

USGS2009

Terrestrial lidar datasets of New Orleans, Louisiana, levee failures from Hurricane Katrina, August 29, 2005

Hurricane Katrina made landfall with the northern Gulf Coast on August 29, 2005, as one of the strongest hurricanes on record. The storm damage incurred in Louisiana included a number of levee failures that led to the inundation of approximately 85 percent of the metropolitan New Orleans area. Whereas extreme levels of storm damage were expected from such an event, the catastrophic failure of the New Orleans levees prompted a quick mobilization of engineering experts to assess why and how particular levees failed. As part of this mobilization, civil engineering members of the United States Geological Survey (USGS) performed terrestrial lidar topographic surveys at major levee failures in the New Orleans area. The focus of the terrestrial lidar effort was to obtain precise measurements of the ground surface to map soil displacements at each levee site, the nonuniformity of levee height freeboard, depth of erosion where scour occurred, and distress in structures at incipient failure. In total, we investigated eight sites in the New Orleans region, including both earth and concrete floodwall levee breaks. The datasets extend from the 17th Street Canal in the Orleans East Bank area to the intersection of the Gulf Intracoastal Waterway (GIWW) with the Mississippi River Gulf Outlet (MRGO) in the New Orleans East area. The lidar scan data consists of electronic files containing millions of surveyed points. These points characterize the topography of each levee’s postfailure or incipient condition and are available for download through online hyperlinks. The data serve as a permanent archive of the catastrophic damage of Hurricane Katrina on the levee systems of New Orleans. Complete details of the data collection, processing, and georeferencing methodologies are provided in this report to assist in the visualization and analysis of the data by future users.

Louisiana↗

USGS2009

The framework of a coastal hazards model: A tool for predicting the impact of severe storms

The U.S. Geological Survey (USGS) Multi-Hazards Demonstration Project in Southern California (Jones and others, 2007) is a five-year project (FY2007-FY2011) integrating multiple USGS research activities with the needs of external partners, such as emergency managers and land-use planners, to produce products and information that can be used to create more disaster-resilient communities. The hazards being evaluated include earthquakes, landslides, floods, tsunamis, wildfires, and coastal hazards. For the Coastal Hazards Task of the Multi-Hazards Demonstration Project in Southern California, the USGS is leading the development of a modeling system for forecasting the impact of winter storms threatening the entire Southern California shoreline from Pt. Conception to the Mexican border. The modeling system, run in real-time or with prescribed scenarios, will incorporate atmospheric information (that is, wind and pressure fields) with a suite of state-of-the-art physical process models (that is, tide, surge, and wave) to enable detailed prediction of currents, wave height, wave runup, and total water levels. Additional research-grade predictions of coastal flooding, inundation, erosion, and cliff failure will also be performed. Initial model testing, performance evaluation, and product development will be focused on a severe winter-storm scenario developed in collaboration with the Winter Storm Working Group of the USGS Multi-Hazards Demonstration Project in Southern California. Additional offline model runs and products will include coastal-hazard hindcasts of selected historical winter storms, as well as additional severe winter-storm simulations based on statistical analyses of historical wave and water-level data. The coastal-hazards model design will also be appropriate for simulating the impact of storms under various sea level rise and climate-change scenarios. The operational capabilities of this modeling system are designed to provide emergency planners with the critical information they need to respond quickly and efficiently and to increase public safety and mitigate damage associated with powerful coastal storms. For instance, high resolution local models will predict detailed wave heights, breaking patterns, and current strengths for use in warning systems for harbor-mouth navigation and densely populated coastal regions where beach safety is threatened. The offline applications are intended to equip coastal managers with the information needed to manage and allocate their resources effectively to protect sections of coast that may be most vulnerable to future severe storms.

California↗

USGS2009

Topographic Change Detection at Select Archeological Sites in Grand Canyon National Park, Arizona, 2006-2007

Topographic change of archeological sites within the Colorado River corridor of Grand Canyon National Park (GCNP) is a subject of interest to National Park Service managers and other stakeholders in the Glen Canyon Dam Adaptive Management Program. Although long-term topographic change resulting from a variety of natural processes is typical in the Grand Canyon region, a continuing debate exists on whether and how controlled releases from Glen Canyon Dam, located immediately upstream of GCNP, are impacting rates of site erosion, artifact transport, and the preservation of archeological resources. Continued erosion of archeological sites threatens both the archeological resources and our future ability to study evidence of past cultural habitation. Understanding the causes and effects of archaeological site erosion requires a knowledge of several factors including the location and magnitude of the changes occurring in relation to archeological resources, the rate of the changes, and the relative contribution of several potential causes, including sediment depletion associated with managed flows from Glen Canyon Dam, site-specific weather patterns, visitor impacts, and long-term climate change. To obtain this information, highly accurate, spatially specific data are needed from sites undergoing change. Using terrestrial lidar data collection techniques and novel TIN- and GRID-based change-detection post-processing methods, we analyzed topographic data for nine archeological sites. The data were collected using three separate data collection efforts spanning 16 months (May 2006 to September 2007). Our results documented positive evidence of erosion, deposition, or both at six of the nine sites investigated during this time interval. In addition, we observed possible signs of change at two of the other sites. Erosion was concentrated in established gully drainages and averaged 12 cm to 17 cm in depth with maximum depths of 50 cm. Deposition was concentrated at specific locations outside of drainages but generally was spread over larger areas (tens to hundreds of square meters). Maximum depths of deposition averaged 12 cm to 15 cm and reached as much as 35 cm. Overall, we found that the spatial distribution and magnitudes of surface change are specific to each site and that a thorough understanding of the geomorphology, weather, and sand supply is requisite for a complete understanding of the data. Additional work in combining these results with site-specific weather, hydrology, and geomorphology data will assist in the development of working models for determining the causes of the documented topographic changes.

Scientific Investigations Report↗

USGS2008

Evaluation of Terrestrial LIDAR for Monitoring Geomorphic Change at Archeological Sites in Grand Canyon National Park, Arizona

This report presents the results of an evaluation of terrestrial light detection and ranging (LIDAR) for monitoring geomorphic change at archeological sites located within Grand Canyon National Park, Ariz. Traditionally, topographic change-detection studies have used total station methods for the collection of data related to key measurable features of site erosion such as the location of thalwegs and knickpoints of gullies that traverse archeological sites (for example, Pederson and others, 2003). Total station methods require survey teams to walk within and on the features of interest within the archeological sites to take accurate measurements. As a result, site impacts may develop such as trailing, damage to cryptogamic crusts, and surface compaction that can exacerbate future erosion of the sites. National Park Service (NPS) resource managers have become increasingly concerned that repeated surveys for research and monitoring purposes may have a detrimental impact on the resources that researchers are trying to study and protect. Beginning in 2006, the Sociocultural Program of the U.S. Geological Survey's (USGS) Grand Canyon Monitoring and Research Center (GCMRC) initiated an evaluation of terrestrial LIDAR as a new monitoring tool that might enhance data quality and reduce site impacts. This evaluation was conducted as one part of an ongoing study to develop objective, replicable, quantifiable monitoring protocols for tracking the status and trend of variables affecting archeological site condition along the Colorado River corridor. The overall study consists of two elements: (1) an evaluation of the methodology through direct comparison to geomorphologic metrics already being collected by total station methods (this report) and (2) an evaluation of terrestrial LIDAR's ability to detect topographic change through the collection of temporally different datasets (a report on this portion of the study is anticipated early in 2009). The main goals of the first element of study were to 1. test the methodology and survey protocols of terrestrial LIDAR surveying under actual archeological site field conditions, 2. examine the ability to collect topographic data of entire archeological sites given such constraints as vegetation and rough topography, and 3. evaluate the ability of terrestrial LIDAR to accurately map the locations of key geomorphic features already being collected by total station methods such as gully thalweg and knickpoint locations. This report focuses on the ability of terrestrial LIDAR to duplicate total station methods, including typical erosion-related change features such as the plan view gully thalweg location and the gully thalweg long profile. The report also presents information concerning the use of terrestrial LIDAR for archeological site monitoring in a general sense. In addition, a detailed comparison of the site impacts caused by both total station and terrestrial LIDAR survey methods is presented using a suite of indicators, including total field survey time, field footstep count, and data-processing time. A thorough discussion of the relative benefits and limitations of using terrestrial LIDAR for monitoring erosion-induced changes at archeological sites in Grand Canyon National Park concludes this report.

Open-File Report↗

USGS2007

Terrestrial LIDAR investigation of the December 2003 and January 2007 activations of the Northridge Bluff landslide, Daly City, California

On December 20, 2003 and again on January 1, 2007, landslides occurred along the coastal bluff that forms the west boundary of Daly City, California sending debris as far as 290 meters downhill and 90 meters into the ocean. This area is known for large landslide events where 150-meter tall coastal bluffs extend southward along the west boundary of San Francisco and San Mateo Counties (Fig. 1). The 2003 and 2007 landslide events occurred west of Northridge Drive in Daly City and just south of Avalon Canyon, which bisects the bluffs in this area (Fig. 2). Residential development, utility lines and roads occupy the land immediately east of this location. As part of a comprehensive project to investigate the failure mechanisms of coastal bluff landslides in weakly lithified sediments along the west coast of the United States, members of the U.S. Geologic Survey (USGS) Coastal and Marine Geology (CMG) Program performed reconnaissance mapping of these landslide events including collection of high-resolution topographic data using CMG's terrestrial LIDAR laser scanning system. This report provides a brief background on each landslide event and presents topographic datasets collected following each event. Downloadable contour data, images, and FGDC-compliant metadata of the surfaces generated from the LIDAR data are also provided. LIDAR data collection and processing techniques used to generate the datasets are outlined. Geometric and volumetric measurements are also presented along with high-resolution cross-sections through various areas of the slide masses and discussion concerning the slides present (2007) configuration is provided.

California↗

USGS2007

High-resolution topographic, bathymetric, and oceanographic data for the Pleasure Point area, Santa Cruz County, California: 2005-2007

The County of Santa Cruz Department of Public Works and the County of Santa Cruz Redevelopment Agency requested the U.S. Geological Survey (USGS) Western Coastal and Marine Geology Team (WCMG) to provide baseline geologic and oceanographic information on the coast and inner shelf at Pleasure Point, Santa Cruz County, California. The rationale for this proposed work is a need to better understand the environmental consequences of a proposed bluff stabilization project on the beach, the nearshore and the surf at Pleasure Point, Santa Cruz County, California. To meet these information needs, the USGS-WCMG Team collected baseline scientific information on the morphology and waves at Pleasure Point. This study provided high-resolution topography of the coastal bluffs and bathymetry of the inner shelf off East Cliff Drive between 32nd Avenue and 41st Avenue. The spatial and temporal variation in waves and their breaking patterns at the study site were documented. Although this project did not actively investigate the impacts of the proposed bluff stabilization project, these data provide the baseline information required for future studies directed toward predicting the impacts of stabilization on the sea cliffs, beach and nearshore sediment profiles, natural rock reef structures, and offshore habitats and resources. They also provide a basis for calculating potential changes to wave transformations into the shore at Pleasure Point.

California↗

USGS2007

Investigation of the M6.6 Niigata-Chuetsu Oki, Japan, earthquake of July 16, 2007

The M6.6 mainshock of the Niigata Chuetsu Oki (offshore) earthquake occurred at 10:13 a.m. local time on July 16, 2007, and was followed by a sequence of aftershocks that were felt during the entire time of the reconnaissance effort. The mainshock had an estimated focal depth of 10 km and struck in the Japan Sea offshore Kariwa. Analysis of waveforms from source inversion studies indicates that the event occurred along a thrust fault with a NE trend. The fault plane is either a strike of 34 degrees with a dip of 51 degrees or a strike of 238 degrees with a dip of 41 degrees. Which of these two planes is associated with the mainshock rupture is unresolved, although attenuation relationship analysis indicates that the northwest-dipping fault is favored. The quake affected an approximately 100-km-wide area along the coastal areas of southwestern Niigata prefecture. The event triggered ground failures as far as the Unouma Hills, located in central Niigata approximately 50 km from the shore and the source area of the 2004 Niigata Chuetsu earthquake. The primary event produced tsunami run-ups that reached maximum runup heights of about 20 centimeters along the shoreline of southern Niigata Prrefecture.

Niigata↗

USGS2006

Land-based lidar mapping: a new surveying technique to shed light on rapid topographic change

The rate of natural change in such dynamic environments as rivers and coastlines can sometimes overwhelm the monitoring capacity of conventional surveying methods. In response to this limitation, U.S. Geological Survey (USGS) scientists are pioneering new applications of light detection and ranging (lidar), a laser-based scanning technology that promises to greatly increase our ability to track rapid topographic changes and manage their impact on affected communities.

Fact Sheet↗

USGS2006

Applicability of terrestrial LIDAR scanning for scientific studies in Grand Canyon National Park, Arizona

In November 2004, an experimental high flow release of water from Glen Canyon Dam into the Colorado River through Grand Canyon National Park in Arizona was conducted. The goal of the experiment was to evaluate the use of high flow events as a management tool for the preservation and restoration of natural resources in the Colorado River below Glen Canyon Dam. The U.S. Geological Survey (USGS), Grand Canyon Monitoring and Research Center (GCMRC) located in Flagstaff, Arizona performed oversight of all aspects of scientific data collection including suspended sediment transport studies, biological population variations, effects on archaeological resources, and morphological studies of river sand bars. As part of the experimental high flow studies, the USGS Coastal and Marine Geology (CMG) team was invited to participate to test the effectiveness of utilizing terrestrial LIDAR technology for gathering morphological data on sand bars, biological habitats, and archaeological sites. The CMG is equipped with a terrestrial LIDAR unit and has used the technique in a variety of terrains to gather high-resolution morphological data. A three-member team from CMG participated in the experiment, joining a GCMRC team on a river trip from November 18 to November 21, 2004. This report begins with a brief description of the LIDAR technique and then outlines the data collected, processing required, and results for three study areas located within the Grand Canyon. Specifically, studies were performed at the Mile 30 Sand Bar, at Vaseys Paradise (Mile 32), and at the Mile 66 Palisades Archaeological Site. Conclusions and recommendations for utilizing terrestrial LIDAR for future studies at each of these sites are also included.

Arizona↗

USGS2005

Field measurements of incision rates following bedrock exposure: Implications for process controls on the long profiles of valleys cut by rivers and debris flows

Until recently, published rates of incision of bedrock valleys came from indirect dating of incised surfaces. A small but growing literature based on direct measurement reports short-term bedrock lowering at geologically unsustainable rates. We report observations of bedrock lowering from erosion pins monitored over 1–7 yr in 10 valleys that cut indurated volcanic and sedimentary rocks in Washington, Oregon, California, and Taiwan. Most of these channels have historically been stripped of sediment. Their bedrock is exposed to bed-load abrasion, plucking, and seasonal wetting and drying that comminutes hard, intact rock into plates or equant fragments that are removed by higher flows. Consequent incision rates are proportional to the square of rock tensile strength, in agreement with experimental results of others. Measured rates up to centimeters per year far exceed regional long-term erosion-rate estimates, even for apparently minor sediment-transport rates. Cultural artifacts on adjoining strath terraces in Washington and Taiwan indicate at least several decades of lowering at these extreme rates. Lacking sediment cover, lithologies at these sites lower at rates that far exceed long-term rock-uplift rates. This rate disparity makes it unlikely that the long profiles of these rivers are directly adjusted to either bedrock hardness or rock-uplift rate in the manner predicted by the stream power law, despite the observation that their profiles are well fit by power-law plots of drainage area vs. slope. We hypothesize that the threshold of motion of a thin sediment mantle, rather than bedrock hardness or rock-uplift rate, controls channel slope in weak bedrock lithologies with tensile strengths below &sim;3–5 MPa. To illustrate this hypothesis and to provide an alternative interpretation for power-law plots of area vs. slope, we combine Shields' threshold transport concept with measured hydraulic relationships and downstream fining rates. In contrast to fluvial reaches, none of the hundreds of erosion pins we installed in steep valleys recently scoured to bedrock by debris flows indicate any postevent fluvial lowering. These results are consistent with episodic debris flows as the primary agent of bedrock lowering in the steepest parts of the channel network above &sim;0.03–0.10 slope.

California, Washington, Oregon↗

USGS2003

Estimating population trends with a linear model

We describe a simple and robust method for estimating trends in population size. The method may be used with Breeding Bird Survey data, aerial surveys, point counts, or any other program of repeated surveys at permanent locations. Surveys need not be made at each location during each survey period. The method differs from most existing methods in being design based, rather than model based. The only assumptions are that the nominal sampling plan is followed and that sample size is large enough for use of the t-distribution. Simulations based on two bird data sets from natural populations showed that the point estimate produced by the linear model was essentially unbiased even when counts varied substantially and 25% of the complete data set was missing. The estimating-equation approach, often used to analyze Breeding Bird Survey data, performed similarly on one data set but had substantial bias on the second data set, in which counts were highly variable. The advantages of the linear model are its simplicity, flexibility, and that it is self-weighting. A user-friendly computer program to carry out the calculations is available from the senior author.

The Condor↗