Geology topics

Alena L. Leeds

Publications and source records attributed to Alena L. Leeds.

6 recordsLinked to original sources

USGS2025

Neotectonic origins for the Meadow Bank scarp, Wabash Valley seismic zone USA

The Meadow Bank scarp (MBS) in southeastern Illinois is a linear geomorphic expression, ∼10 km long and ∼8 m high above a relatively flat landscape. It parallels an underlying northeast‐oriented Late‐Precambrian–Early‐Cambrian structural fabric, called the Wabash Valley fault zone, and is within an area of modern, historic, and paleo seismicity, called the Wabash Valley seismic zone. In addition, the MBS acts as a boundary of the Wabash River floodplain, as well as Pleistocene glacial outwash channels, which show evidence of frequent outburst flood events. To better understand the MBS’s equivocal origin in this complex geologic environment, we acquired a 917‐m‐long seismic‐reflection survey across its axis to assess the subsurface geologic configuration. The resultant image indicates a complex set of faults that antiformally fold and displace the top of Paleozoic bedrock by ∼12 m across the survey. Moreover, fault and/or fold deformation extends into the shallowest imaged Quaternary strata at ∼6 m below the ground surface. This suggests the MBS origin is related to underlying Quaternary reactivated, positively inverted faults rather than exclusively to glacial outburst flood erosion. These results provide rare paleoearthquake spatial constraints for central U.S. regional seismic hazard consideration.

Illinois↗

USGS2024

Site response in the Walnut Creek–Concord region of the San Francisco Bay, California: Ground motion amplification in a fault-bounded basin

Thirty‐seven portable accelerometers were deployed in the eastern San Francisco Bay communities of Walnut Creek and Concord to study site response in a fault‐bounded, urban, sedimentary basin. Local earthquakes were recorded for a period of two years from 2017 to 2019 resulting in 101 well‐recorded events. Site response is estimated by two methods: the reference site spectral ratio method and a source‐site spectral inversion method. The reference site spectral ratio method allows investigation of the variability of site amplification with source azimuth and frequency. The source‐site spectral inversion method yields the best least‐squares fit to site response for a database of ground‐motion records. Both methods show substantial amplification in the Walnut Creek–Concord basin below 2 Hz indicating strong surface‐wave development. Greater amplification is seen for sources aligned along the long axis of the basin. Inversion using close‐in sources at short distances yields lower amplification at longer periods than the entire data set due to reduced surface‐wave generation for steeper angles of incidence. Inversion of site response spectra for shallow shear‐wave velocity using a global search algorithm yields V S30 values consistent with generalized mapping results based on geology and topography but with greater variability due to local site variations. 3D finite‐element modeling shows greater amplification in the Walnut Creek–Concord basin with a basin‐edge effect likely contributing to higher ground motions. Topography is also seen to lead to increased scattering and shadowing effects.

California↗

USGS2021

Shear-wave velocity site characterization in Oklahoma from joint inversion of multi-method surface seismic measurements: Implications for central U.S. Ground Motion Prediction

We analyze multimethod shear (SH)‐wave velocity ( ⁠ V S "> V S ) site characterization data acquired at three permanent and 25 temporary seismograph stations in Oklahoma that recorded M 4+ earthquakes within a 50 km hypocentral distance of at least one of the 2016 M 5.1 Fairview, M 5.8 Pawnee, or M 5.0 Cushing earthquakes to better constrain earthquake ground‐motion modeling in the region. We acquired active‐source seismic data for time‐averaged V S "> V S to 30 m depth ( V S "> V S V S 30 "> 30 ) at 28 seismograph stations near the Fairview, Pawnee, and Cushing epicentral areas. The SH‐wave refraction travel times coupled with Rayleigh‐ and Love‐wave phase velocity dispersion were extracted and modeled in a nonlinear least‐squares (L2) joint inversion to obtain a best‐fit 1D V S "> V S versus depth profile for each site. At a subset of sites where the preferred L2 inverse model did not optimally fit each of the Love, Rayleigh, and SH travel‐time datasets, we explore application of simulated annealing in a joint inversion to find a more global solution. V S "> V S V S 30 "> 30 values range from 262 to 807    m / s "> 807 m / s for the preferred measured (in situ) V S "> V S profiles, or National Earthquake Hazards Reduction Program (NEHRP) site class D to B, and are broadly comparable with estimates from previous data reports in the region. Site amplification estimates were calculated next from 1D SH transfer functions of the preferred V S "> V S VS profiles and then compared against observed horizontal‐to‐vertical spectral ratios (HVSRs) from nearby seismograph stations. We generally see good agreement between the predicted in situ model and the observed HVSR resonant frequencies, with nominal amplifications between 2 and 10 within the 2–15 Hz frequency band. Next, using 40 known in situ V S "> V S V S 30 "> 30 measurements in the region, we demonstrate that the in situ V S "> V S V S 30 "> 30 values improve the fit for selected suites of ground‐motion models (GMMs) for M 4+ earthquakes within a 50 km hypocentral distance when compared with proxy methods, arguing for future development of GMMs implementing in situ V S "> V S profiles.

Oklahoma↗

USGS2017

Seismic response of soft deposits due to landslide: The Mission Peak, California, landslide

The seismic response of active and intermittently active landslides is an important issue to resolve to determine if such landslides present an elevated hazard in future earthquakes. To study the response of landslide deposits, seismographs were placed on the Mission Peak landslide in the eastern San Francisco Bay region for a period of one year. Numerous local and near‐regional earthquakes were recorded that reveal a complexity of seismic response phenomena using the horizontal‐to‐vertical spectral ratio method. At lower frequencies, a clear spectral peak is observed at 0.5 Hz common to all four stations in the array and is attributed to a surface topographic effect. At higher frequencies, other spectral peaks occur that are interpreted in terms of local deposits and structures. Site amplification from the standard reference site method shows the minimum amplification with a factor of 2, comparing a site on and off the landslide. A site located on relatively homogeneous deposits of loose soils shows a clear spectral peak associated with the thickness of the deposit. Another site on a talus‐filled graben near the headscarp shows possible 2D or 3D effects from subsurface topography or scattering within and between buried sandstone blocks. A third site on a massive partially detached block below the crown of the headscarp shows indications of resonance caused by the reverberation of shear waves within the block. The varied seismic response of different parts of this complex landslide is consistent with other studies which found that, although landslide response is commonly enhanced in the downslope direction of landslide movement, such a response does not occur uniformly or consistently. When it does occur, enhanced site response parallel to the direction of landslide movement would contribute to landslide reactivation during significant earthquakes.

California↗

USGS2016

Ground motion in the presence of complex Topography II: Earthquake sources and 3D simulations

Eight seismic stations were placed in a linear array with a topographic relief of 222 m over Mission Peak in the east San Francisco Bay region for a period of one year to study topographic effects. Seventy‐two well‐recorded local earthquakes are used to calculate spectral amplitude ratios relative to a reference site. A well‐defined fundamental resonance peak is observed with individual station amplitudes following the theoretically predicted progression of larger amplitudes in the upslope direction. Favored directions of vibration are also seen that are related to the trapping of shear waves within the primary ridge dimensions. Spectral peaks above the fundamental one are also related to topographic effects but follow a more complex pattern. Theoretical predictions using a 3D velocity model and accurate topography reproduce many of the general frequency and time‐domain features of the data. Shifts in spectral frequencies and amplitude differences, however, are related to deficiencies of the model and point out the importance of contributing factors, including the shear‐wave velocity under the topographic feature, near‐surface velocity gradients, and source parameters.

California↗

USGS2016

Seismic site characterization of an urban dedimentary basin, Livermore Valley, California: Site tesponse, basin-edge-induced surface waves, and 3D simulations

Thirty‐two accelerometers were deployed in the Livermore Valley, California, for approximately one year to study sedimentary basin effects. Many local and near‐regional earthquakes were recorded, including the 24 August 2014 M w 6.0 Napa, California, earthquake. The resulting ground‐motion data set is used to quantify the seismic response of the Livermore basin, a major structural depression in the California Coast Range Province bounded by active faults. Site response is calculated by two methods: the reference‐site spectral ratio method and a source‐site spectral inversion method. Longer‐period (≥1  s) amplification factors follow the same general pattern as Bouguer gravity anomaly contours. Site response spectra are inverted for shallow shear‐wave velocity profiles, which are consistent with independent information. Frequency–wavenumber analysis is used to analyze plane‐wave propagation across the Livermore Valley and to identify basin‐edge‐induced surface waves with back azimuths different from the source back azimuth. Finite‐element simulations in a 3D velocity model of the region illustrate the generation of basin‐edge‐induced surface waves and point out strips of elevated ground velocities along the margins of the basin.

Bulletin of the Seismological Society of America↗